Televes OLT 769401 User Manual Download Page 206

Page: 206 / 482

Descripción del producto

206

7.6.1.12.2 “create” command

Name

Create

Description

Create a new MAC Rule for a given ACL ID.

Full path

/acl/rule-mac/create

Mandatory Parameters

--acl-id
--action

Screen Output

Table 7-32: “create” command information

/cli/acl/rule-mac> create ?

Usage:

CREATE Create a new MAC Rule for a given ACL ID.

--acl-id Identifies an ACL by ID, in this context.

--action permit or deny

[OPTIONAL]

--admin Administrative State. Enable/disable, in this context.

(enable|disable)

--cos Match condition based on the CoS value (not-used|0..7)

--dst-mac-addr Destination MAC address in the format [AA:BB:CC:DD:EE:FF]

--dst-mac-mask Destination MAC mask in the format [AA:BB:CC:DD:EE:FF]

--ethernet-type Four-digit hexadecimal number to specify an ‘Ethertype’ value (not-

used|0X600..0XFFFF)

--name Set a name for a specific Rule (STRING 31)

--rule-id Identifies an ACL Rule by ID, in this context.

--src-mac-addr Source MAC address in the format [AA:BB:CC:DD:EE:FF]

--src-mac-mask Source MAC mask in the format [AA:BB:CC:DD:EE:FF]

Figure 7-50: CLI on line help on “create” command usage in this node context

7.6.1.12.3 “show” command

Name

show

Description

Show the current MAC Rules configured.

Full path

/acl/rule-mac/show

Mandatory Parameters

No mandatory parameters

Screen Output

Table Figure 7-60; Table parameters are described in Table 7-34.

Table 7-33: “show” command information

/cli/acl/rule-mac> show ?

Usage:

SHOW Show the current MAC rules configured.

[OPTIONAL]

--acl-id Identifies an ACL by ID, in this context.

Figure 7-51: CLI on line help on “show” command usage in this node context

Summary of Contents for OLT 769401



































































































































































































































































































































































































































































































Search results

Summary of Contents for OLT 769401

Reviews:

Related manuals for OLT 769401

Brands by name

Popular brands

Televes OLT 769401, User Manual

Search results

Summary of Contents for OLT 769401

Reviews:

Related manuals for OLT 769401

Brands by name

Popular brands