Televes OLT 769401 User Manual Download Page 375

Page: 375 / 482

375

/cli/remote-eq/onu/ext-vlan-tag-op> config ?

Usage:

CONFIG

Configure the Extended VLAN Tagging Operation Global Attributes

--onu-port

Identifies an interface on the ONU

[OPTIONAL]

--dscp-to-pbit-profile-id Specifies the profile for mapping DSCP to P bits

--enable

Enable/disable Extended VLAN Tagging operations on the

specified ONU port. (enable|disable)

--input-tpid

Special TPID value for operations on the input (filtering) side

of the table in HEX format.

--onuID

Identifies an ONU by ID, in this context.

--output-tpid

Special TPID value for operations on the output (tagging) side

of the table in HEX format.

--port

Identifies an interface on the OLT. (e.g.: pon.2; eth.3; lag.1)

Figure 7-423: CLI on line help on “config” command usage in this node context

7.6.17.6.6.2 “show” command

Name

show

Description

Show Extended VLAN Tagging Operation information on this ONU

Full path

/ remote-eq/onu/ ext-vlan-tag-op/show

Mandatory Parameters

Screen Output

Table, Figure 7-424. Table parameters description in Table 7-385..

Table 7-384: “show” command information

/cli/remote-eq/onu/ext-vlan-tag-op> show ?

Usage:

SHOW Show Extended VLAN Tagging Operation information on this ONU.

[OPTIONAL]

--onuID Identifies an ONU by ID, in this context.

--port Identifies an interface on the OLT. (e.g.: pon.2; eth.3; lag.1)

Figure 7-424: CLI on line help on “show” command usage in this node context

Figure 7-425: show command - output in this node context

Summary of Contents for OLT 769401



































































































































































































































































































































































































































































































Search results

Summary of Contents for OLT 769401

Reviews:

Related manuals for OLT 769401

Brands by name

Popular brands

Televes OLT 769401, User Manual

Search results

Summary of Contents for OLT 769401

Reviews:

Related manuals for OLT 769401

Brands by name

Popular brands