Televes OLT 769401 User Manual Download Page 253

Page: 253 / 482

253

7.6.8.3 “create” command

Name

create

Description

Create a new Protection Group.

Full path

/eth-protection/create

Mandatory Parameters

Screen Output

Table 7-130: “create” command information

/cli/eth-protection> create ?

Usage:

CREATE Create a new ethernet Protection Group..

[OPTIONAL]

--ID Identifies a table entry by ID, in this context.

--admin Administrative State. Enable/disable, in this context.

(enable|disable)

--hold-off-time Hold Off Time (0..100) x100ms

--hp-lc-fail high priority: Generalized Line Card Failure (enable|disable)

--hp-los high priority: Generalized LOS (enable|disable)

--p-port Identifies the Protecting Interface ID.

--reversible Specify is reversion is enabled (enable|disable)

--w-port Identifies the Working Interface ID.

--wtr-time Wait to Restore Time (WTR) (5..12) min [OPTIONAL]

--auto-removal

User’s auto-removal (enable|disable)

--expire-time

User’s expire time (hours)

Figure 7-156: CLI on line help on “create” command usage in this node context

7.6.8.4 “remove” command

Name

remove

Description

Remove an existing Protection Group

Full path

/eth-protection/remove

Mandatory Parameters

--ID

Screen Output

Table 7-131: “remove” command information

/cli/eth-protection> remove ?

Usage:

REMOVE Remove an existing ethernet Protection Group.

--ID Identifies a table entry by ID, in this context.

Figure 7-157: CLI on line help on “remove” command usage in this node context

Summary of Contents for OLT 769401



































































































































































































































































































































































































































































































Search results

Summary of Contents for OLT 769401

Reviews:

Related manuals for OLT 769401

Brands by name

Popular brands

Televes OLT 769401, User Manual

Search results

Summary of Contents for OLT 769401

Reviews:

Related manuals for OLT 769401

Brands by name

Popular brands