Televes OLT 769401 User Manual Download Page 240

Page: 240 / 482

Descripción del producto

240

/cli/equipment/slot> config ?

Usage:

CONFIG Configure HW slots (not immediately applied)

--mode

Specify the mode (modeA|modeB|modeC)

Figure 7-129: CLI on line help on “config” command usage in this node context

7.6.6.3.3 “show” command

Name

show

Description

Show the current Slot-Mode configuration.

Full path

/equipment/slot/show

Mandatory Parameters

This command has no parameters.

Screen Output

Tables, Figure 7-131.Tables parameter description Table 7-107

Table 7-106: “show” command information

/cli/equipment/slot> show ?

Usage:

SHOW Show the current Slot-Mode configuration.

Figure 7-130: CLI on line help on “show” command usage in this node context

Figure 7-131: Output of ”show” command in this node context

Parameter

Description

Slot

Slot number

Card Name

Name of the card in the specified slot

Card Status

Card status (newboard|operational|configuration error|absent|proc.)

Admin

Board administrative State

Config. Mode

Configured mode on card (Mode A|Mode B|Mode C)

FW Mode

Detected firmware mode on card (Mode A|Mode B|Mode C)

FW Status

Card firmware Status (OK|Disabled|Unsupported mode for this card)

Table 7-107: “show” command output table parameters

7.6.6.3.4 showconfig” command

Name

showconfig

Description

Print the command list that enforces the current configuration

Full path

/equipment/slot/showconfig

Mandatory Parameters

This command has no parameters

Summary of Contents for OLT 769401



































































































































































































































































































































































































































































































Search results

Summary of Contents for OLT 769401

Reviews:

Related manuals for OLT 769401

Brands by name

Popular brands

Televes OLT 769401, User Manual

Search results

Summary of Contents for OLT 769401

Reviews:

Related manuals for OLT 769401

Brands by name

Popular brands