Televes OLT 769401 User Manual Download Page 48

Page: 48 / 482

Descripción del producto

4.3.1 Restricted Access Location

The OLT Ref.769401 unit is to be installed in a restricted access location.

4.4 Electrical Power Supply

The electrical connection for the OLT equipment is of redundant -48VDC.

4.4.1 Disconnect Device

A Disconnect Device must be installed close to unit chassis in order to allow disconnection of all power supply before servicing the unit.

In the case of installation in an ETSI rack, rack installed Power Box, provides disconnect device funcionality

Disconnect device circuit breaker should be rated 3A max.

4.4.2 Multiple Power Source

Power supply to the unit is provided by two 48 VN(egative) power supply source connection, source A and source B.

Important!

All unit power supply must be disconnected at the disconnect device before servicing the unit.

4.4.3 Power Supply Connection Procedures

Important!

When performing OLT system service actions, observe electrostatic discharge (ESD) precautions, ESD

All unit power supply must be disconnected at the disconnect device before servicing the unit.

4.4.4 Power Supply Cables Connection

In right side of the OLT front panel there are two tree input connectors for power supply connections P1 and P2, (see Figure 4-2):

Figure 4-2: OLT chassis redundant power supply input connectors

Step 1

Use the H03VV-F conducting electrical cables with eyelet terminals provided in the OLT mounting kit to connect the two

redundant power supplies.

Summary of Contents for OLT 769401



































































































































































































































































































































































































































































































Search results

Summary of Contents for OLT 769401

Reviews:

Related manuals for OLT 769401

Brands by name

Popular brands

Televes OLT 769401, User Manual

Search results

Summary of Contents for OLT 769401

Reviews:

Related manuals for OLT 769401

Brands by name

Popular brands