Televes OLT 769401 User Manual Download Page 466

Page: 466 / 482

Descripción del producto

466

0x1D034893

Only one multicast service is allowed per ONU

0x1D034894

Network Service already associated with another Client Service (same ONU).

0x1D034895

NNI C-Tag is in use by another ONU

0x1D034896

NNI C-Tag < min

0x1D034897

NNI C-Tag > max

0x1D034898

MAX service num

0x1D034899

(multicast) NNI C-Tag cannot be zero

0x1D03489A

The NNI C-TAG can’t be 0 for unicast stacked services

0x1D03489B

service has attached ONU interface(s)

0x1D03489C

OLT service does not include this ONU interface

0x1D03489D

service has attached interfaces(s)

0x1D03489F

Reached Maximum nbr of downstream services for this Slot

0x1D0348B0

max Upstream BW

0x1D0348BA

VoIP services can only have VoIP interfaces

0x1D0348BB

VoIP services must have at least one VoIP interface

0x1D0348BC

The unicast service associated is admin disabled 0x1D0348BD The multicast

service associated is admin enabled

0x1D0348BE

Invalid DHCP configurations

0x1D0348BF

Invalid remote-id string

0x1D0348C0

Unable to configure more than one unicast IGMP service per ONU

0x1D0348C1

No unicast IGMP service for this ONU

0x1D0348C2

No active unicast IGMP service for this ONU

0x1D0348C3

IP Management can only be configured for unicast services

0x1D0348C4

Requested ONU cannot have more than one service with IP Management

0x1D0348C5

Encryption flag cannot be used in multicast services

0x1D0348C6

All multicast services must be deactivated prior to deactivating the unicast IGMP

service

0x1D0348C7

Unable to remove service Bridge master until the remaing Bridge services are

removed

0x1D0348C8

Unable to configure a downstream traffic profile on unstacked services

0x1D0348C9

NNI C-Tag is used by another Client Service associated with a Network Service

with the same NNI S-Tag

0x1D0348CA

The selected ethernet profile does not exist

0x1D0348CB

The selected upstream profile does not exist

0x1D0348CC

The service has no T-CONTs mapping

0x1D0348CD

The service has T-CONTs mapping

0x1D0348CE

Invalid PCP profile

0x1D035010

Duplicated Client Service referencing the same Unstacked Network Service on this

Interface

0x1D035011

Requested NNI C-Tag does not match the remaining ONUs assoc

iated with the same N:1 Bridge OltService

0x1D035012

EthernetProfileId MUST match for all OntServices that belong to the same ONU

and N:1 Bridge OltService

0x1D035013

EthernetProfileId MUST match for all OntServices that belong to the same card

and 1:1 Bridge OltService

0x1D035014

Client Service has no interface associated

0x1D035015

Unstacked Services: Duplicated UNI C-TAG --Stacked Services: UNI C-TAG cannot

duplicate NNI C-TAG

0x1D035016

Duplicated UNI-CTAG for the chosen service type

0x1D035020

The network service has no IGMP

0x1D035021

IGMP override flag cannot be done on active service 0x1D035030 Maximum

number of MACs out of range

0x1D035031

Maximum number of MACs not supported for service type

0x1D035032

Extended VLAN tagging is active in a service port

0x1D035033

The service is referenced by Extended VLAN tagging rules

0x1D039211

The upstream profile can’t be changed with upstream profiles

0x1D039212

The type of the upstream traffic profile is invalid

0x1D039213

Invalid parameter for upstream traffic profile

0x1D039214

Empty String for Profile name

0x1D039215

The specified ONU profile ID does not exist

Summary of Contents for OLT 769401



































































































































































































































































































































































































































































































Search results

Summary of Contents for OLT 769401

Reviews:

Related manuals for OLT 769401

Brands by name

Popular brands

Televes OLT 769401, User Manual

Search results

Summary of Contents for OLT 769401

Reviews:

Related manuals for OLT 769401

Brands by name

Popular brands