Televes OLT 769401 User Manual Download Page 283

Page: 283 / 482

283

7.6.10.2.2 “show” command

Name

show

Description

Shows PON information for a specific HW slot.

Full path

/interfaces/gpon/show

Mandatory Parameters

Screen Output

Table, Figure 7-220. Table parameter description in Table 7-194.

Table 7-193: “show” command information

/cli/interfaces/gpon> show ?

Usage:

SHOW Shows PON information for a specific HW slot.

Figure 7-219: CLI on line help on “show” command usage in this node context

Figure 7-220: Output of “show” command used with argument –slot, in this node context

Parameter

Description

GPON Interface identifier (number)

Name

GPON interface name

Admin

Administrative GPON interface Status (enabled|disabled)

Mac Aging (sec)

Time it takes for a MAC address to be removed from the GPON MAC table, in

the case it hasn’t been received any packet with that source address in that

GPON port. This value must be in the range between 120 and 3600 seconds.

(Note: The MAC addresses in the GPON interface are only learnt in Unicast

Unstacked Services)

Max distance (Km)

Maximum distance for which the interface can detect ONU’s. The difference

between the minimum and the maximum can’t exceed 20km, and the

maximum distance can’t be higher than 60km

Min. distance (Km)

Minimum distance for which the interface can detect ONU’s. The difference

between the minimum and the maximum can’t exceed 20km, and the

maximum distance can’t be higher than 60km

BER (s)

PON port Bit Error Rate in the downstream in sec

Downstream FEC

Flag; Downstream FEC enabled at this PON port if selected

ONU Auto Discovery

Flag; Auto Discovery ONUs at this PON port enabled if selected

MTU

MTU configured value

IP SRc. Guard

Flag; IP Source Guard enabled if selected

Mapping Mode

Used Mapping mode ( VLAN | VLAN + P-bits)

Table 7-194: show command with argument slot - output table parameters

Summary of Contents for OLT 769401



































































































































































































































































































































































































































































































Search results

Summary of Contents for OLT 769401

Reviews:

Related manuals for OLT 769401

Brands by name

Popular brands

Televes OLT 769401, User Manual

Search results

Summary of Contents for OLT 769401

Reviews:

Related manuals for OLT 769401

Brands by name

Popular brands