Televes OLT 769401 User Manual Download Page 400

Page: 400 / 482

Descripción del producto

400

/cli/remote-eq/status/ethernet/statistics> show ?

Usage:

SHOW Show ethernet statistics

--remote-port

Identifies an interface on a remote device.

[OPTIONAL]

--onuID

Identifies an ONU by ID, in this context.

--port

Identifies an interface on the OLT. (e.g.: pon.2; eth.3; lag.1)

Figure 7-467: CLI on line help on “show” command usage in this node context

Figure 7-468: Output of ”show” command in this node context

Parameter

Description

Rx Total & Partial

Received total & partial counters

Tx Total & Partial

Transmitted total & partial counters

Drop Events

Number of dropped packets

Octets

Number of bytes

Packets

Number of Packets

Unicast Packets

Number of Unicast Packets

Broadcast Packets

Number of Broadcast Packets

Multicast Packets

Number of Multicast Packets

CRC Align Errors

Number of packets with wrong FCS (Frame Check Sequence)

Undersize Packets

Number of packets with size less than 64 bytes

Oversize Packets

Number of packets with size over than 1518 bytes

Fragments

Number of packets with size less than 64 bytes and with wrong FCS (Frame

Check Sequence)

Jabbers

Number of packets with size over than 1518 bytes and with wrong FCS (Frame

Check Sequence)

Collisions

Number of collisions in the Ethernet Segment (only in Half Duplex)

Packets 64 Octets

Number of 64 bytes packets

Packets 65-127 Octets

Number of packets with size between 65 to 127 bytes

Packets 128-255 Octets

Number of packets with size between 128 to 255 bytes

Packets 256-511 Octets

Number of packets with size between 256 to 511 bytes

Packets 512-1023 Octets

Number of packets with size between 512 to 1023 bytes

Packets >=1024 Octets

Number of packets with size equal to or higher than 1024 bytes

Table 7-433: show command – output table parameters

Summary of Contents for OLT 769401



































































































































































































































































































































































































































































































Search results

Summary of Contents for OLT 769401

Reviews:

Related manuals for OLT 769401

Brands by name

Popular brands

Televes OLT 769401, User Manual

Search results

Summary of Contents for OLT 769401

Reviews:

Related manuals for OLT 769401

Brands by name

Popular brands