Televes OLT 769401 User Manual Download Page 333

Page: 333 / 482

333

/cli/multicast/probes> create ?

Usage:

CREATE Create a Probe for a multicast service uplink interface.

--ip-mcast[=STRING] IPv4 multicast address

--port

Identifies an interface on the OLT. (e.g.: pon.2; eth.3; lag.1)

--serviceID

Select an OLT service by ID.

[OPTIONAL]

--admin

Administrative State. Enable/disable, in this context.

(enable|disable)

Figure 7-332: CLI on line help on “create” command usage in this node context

7.6.15.4.3 ”remove” command

Name

remove

Description

Remove an existing Probe.

Full path

/multicast/probes/remove

Mandatory Parameters

--ID

Screen Output

Table 7-297: “remove” command information

/cli/multicast/probes> remove ?

Usage:

REMOVE Remove an existing Probe.

--ID

Identifies a table entry by ID, in this context.

Figure 7-333: CLI on line help on “remove” command usage in this node context

7.6.15.4.4 ”show” command

Name

show

Description

Show the current multicast probes configuration.

Full path

/multicast/probes/show

Mandatory Parameters

This command has no parameters

Screen Output

Tables, Figure 7-335. Table parameters description, Table 7-299.

Table 7-298: “show” command information

/cli/multicast/probes> show ?

Usage:

SHOW Show the current multicast probes configuration.

Figure 7-334: CLI on line help on “show” command usage in this node context

Summary of Contents for OLT 769401



































































































































































































































































































































































































































































































Search results

Summary of Contents for OLT 769401

Reviews:

Related manuals for OLT 769401

Brands by name

Popular brands

Televes OLT 769401, User Manual

Search results

Summary of Contents for OLT 769401

Reviews:

Related manuals for OLT 769401

Brands by name

Popular brands