Televes OLT 769401 User Manual Download Page 135

Page: 135 / 482

135

with a DNU (Do Not Use) status in QL mode enabled. Otherwise, this command is automatically rejected.

Moreover, in the QL mode, manual switching may be performed only for the source that has the highest available QL.

Thus, these conditions have the effect that a manual switch can only be used to override the priorities of the assigned

synchronism sources. A request for manual switching overrides any other earlier request for manual switching.

This command is disabled using Clear command.

Force Switch

(at Global Parameters table):

Causes switching to the selected synchronism source even if it has a failure.

This command can be used to implement the currently selected synchronism source, by assuming that the synchronism

source is enabled and not in a Locked Up state. Otherwise, this command is automatically rejected.

This command overrides manual switching and another later Force Switch command overrides this.

This command is disabled by the Clear command.

Important!

A Force Switch command sent to a synchronism source that has a Signal Fail status, or has a DNU QL mode enabled, will result in that network

element entering an Holdover state.

6.2.2.2 PTP

Figure 6-5: PTP Status window

Summary of Contents for OLT 769401



































































































































































































































































































































































































































































































Search results

Summary of Contents for OLT 769401

Reviews:

Related manuals for OLT 769401

Brands by name

Popular brands

Televes OLT 769401, User Manual

Search results

Summary of Contents for OLT 769401

Reviews:

Related manuals for OLT 769401

Brands by name

Popular brands