Televes OLT 769401 User Manual Download Page 261

Page: 261 / 482

261

/cli/interfaces/ethernet> config ?

Usage CONFIG:

CONFIG Configure the given Ethernet interface

--port Identifies an interface on the OLT. (e.g.: pon.2; eth.3; lag.1)

[OPTIONAL]

--admin Administrative State. Enable/disable, in this context.

(enable|disable)

--esmc Enables sending SSM packets over ESMCChannel. (enable|disable)

--ip-source-guard Enable/Disable IP Source Guard filtering for the specified

interface. (enable|disable)

--media-type Media Type (100-base-X-full|1000-base-X-full-auto-neg-on|1000-

base-X-full-auto-neg-off|1000-base-T-full-auto-neg-off|10G-base-

--mtu Sets the Maximum Transmission Unit, which corresponds to the

largest packet that can be transmitted(1518..9600 Bytes).

--timeout Set the timeout used by the LACPDUs packets (short|long)(1s|30s)

Figure 7-174: CLI on line help on “config” command usage in this node context

7.6.10.1.2 “show” command

Name

show

Description

Show the current configuration.

Full path

/interfaces/ethernet/show

Mandatory Parameters

Screen Output

Tables, Figure 7-176 Tables parameter description in Table 7-141

Table 7-147: “show” command information

/cli/interfaces/ethernet> show ?

Usage:

SHOW Shows Ethernet information for a specific slot.

Figure 7-174: CLI on line help on “show” command usage in this node context

Figure 7-176: Output of “show” command, without arguments, in this node context

Summary of Contents for OLT 769401



































































































































































































































































































































































































































































































Search results

Summary of Contents for OLT 769401

Reviews:

Related manuals for OLT 769401

Brands by name

Popular brands

Televes OLT 769401, User Manual

Search results

Summary of Contents for OLT 769401

Reviews:

Related manuals for OLT 769401

Brands by name

Popular brands