Televes OLT 769401 User Manual Download Page 377

Page: 377 / 482

377

/cli/remote-eq/onu/ext-vlan-tag-op/operation-table> config ?

Usage CONFIG:

CONFIG Configure an Extended VLAN Tagging Operation Table entry

--ID Identifies a table entry by ID, in this context.

--onu-port Identifies an interface on the ONU

[OPTIONAL]

--admin Administrative State. Enable/disable, in this context.

(enable|disable)

--f-ethertype Filter by ETHERTYPE (any|IPoE|PPPoE|ARP|IPv6_IPoE)

--f-inner-priority Filter by Inner Priority (0..7|any)

--f-inner-tpid Filter by Inner TPID (any|8100|input-dei-any|input-dei-0|input-

dei-1)

--f-inner-vid Filter by Inner VID

--onuID Identifies an ONU by ID, in this context.

--port Identifies an interface on the OLT. (e.g.: pon.2; eth.3; lag.1)

--serviceID-onu Choose a ONU service by ID.

--t-op-vid Treatment - VID Operation (add|replace|discard)

--t-priority Treatment - Priority (0..7|copy|derive-from-dscp)

--t-tpid Treatment - TPID (0x8100)

Figure 7-427: CLI on line help on “config” command usage in this node context

7.6.17.6.6.4.2 “create” command

Name

create

Description

Create an Extended VLAN Tagging Operation Table entry

Full path

/remote-eq/onu/ext-vlan-tag-op/operation-table/config

Mandatory Parameters

--onu-port
--type

Screen Output

Table 7-388: “create” command information

Summary of Contents for OLT 769401



































































































































































































































































































































































































































































































Search results

Summary of Contents for OLT 769401

Reviews:

Related manuals for OLT 769401

Brands by name

Popular brands

Televes OLT 769401, User Manual

Search results

Summary of Contents for OLT 769401

Reviews:

Related manuals for OLT 769401

Brands by name

Popular brands