Suzuki SWIFT RS415 2017 Скачать руководство пользователя страница 1 | Manualshive

Страница: 1 / 1257

background image

IMPORTANT

WARNING/CAUTION/NOTE

Please read this manual and follow its instructions carefully. To emphasize special information, the words

WARNING, CAUTION

and

NOTE

have special meanings. Pay special attention to the messages highlighted by

these signal words.

The circle with a slash in this manual means “Don’t do this” or “Don’t let this happen”.

WARNING:
Indicates a potential hazard that could result in death or injury.

CAUTION:
Indicates a potential hazard that could result in vehicle damage.

NOTE:
Indicates special information to make maintenance easier or instructions clearer.

WARNING:
This service manual is intended for authorized Suzuki dealers and qualified service technicians only.
Inexperienced technicians or technicians without the proper tools and equipment may not be able to
properly perform the services described in this manual.
Improper repair may result in injury to the technician and may render the vehicle unsafe for the driver
and passengers.

WARNING:
For vehicles equipped with a Supplemental Restraint or Air Bag System:
• Service on and around the air bag system components or wiring must be performed only by an

authorized SUZUKI dealer. Refer to “Air Bag System Components and Wiring Location View” under
“General Description” in air bag system section in order to confirm whether you are performing ser-
vice on or near the air bag system components or wiring. Please observe all WARNINGS and “Ser-
vice Precautions” under “On-Vehicle Service” in air bag system section before performing service
on or around the air bag system components or wiring. Failure to follow WARNINGS could result in
unintentional activation of the system or could render the system inoperative. Either of these two
conditions may result in severe injury.

• If the air bag system and another vehicle system both need repair, Suzuki recommends that the air

bag system be repaired first, to help avoid unintended air bag system activation.

• Do not modify the steering wheel, instrument panel or any other air bag system component on or

around air bag system components or wiring. Modifications can adversely affect air bag system
performance and lead to injury.

• If the vehicle will be exposed to temperatures over 93°C (200°F), for example, during a paint baking

process, remove the air bag system components, that is air bag or inflator modules, SDM and/or
seat belt with pretensioner, beforehand to avoid component damage or unintended activation.

1
2
3
...
»

Содержание SWIFT RS415 2017










































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для SWIFT RS415 2017

Бренд: Yakima Страницы: 8

Бренд: Xblitz Страницы: 16

CommCenter D1 Series

Бренд: Federal Signal Corporation Страницы: 16

AAB-P-RZR900-K2-001

Бренд: SuperATV Страницы: 3

2011 Civic Sedan

Бренд: Honda Страницы: 5

990E0-54P56-000

Бренд: Suzuki Страницы: 12

Car Cup Holder Phone Mount

Бренд: UGREEN Страницы: 9

Code Alarm PROFESSIONAL SERIES CA 5550SST

Бренд: Audiovox Страницы: 14

Бренд: STC Страницы: 6

VIEWLINE 52 MM - MOUNTING 11-09

Бренд: VDO Страницы: 4

Бренд: Yakima Страницы: 12

Бренд: Axxess Страницы: 16

Бренд: JSPORT Страницы: 2

PRIME DESIGN VRR3-FT21G-ST

Бренд: Safe Fleet Страницы: 12

2013 2500 Big Horn

Бренд: RAM Страницы: 12

IT FITS RBO1018

Бренд: RBO Страницы: 36

CMPC-22 Fujitsu-Siemens PocketLoox 410

Бренд: Carcomm Страницы: 2

2000 Accord Sedan

Бренд: Honda Страницы: 320

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды