manualshive.com logo in svg

Hitachi H8S/2196, Hardware Manual

The Hitachi H8S/2196 is a high-performance microcontroller designed for various hardware applications. To unlock its full potential, simply visit our website and download the free hardware manual. Find all the essential information you need to maximize your product experience at manualshive.com.

Share
Download
background image

Rev. 1.0, 02/00, page 769 of 1141

Bit 5

Reference Hsync Signal Select (HSEL): Selects the reference Hsync signal for the AFC:

the external Hsync signal or the internally generated Hsync signal. When using the data slicer,
select the external Hsync signal. When not using the data slicer but using the text display mode for
the OSD, select the internally generated Hsync signal. Before this bit setting is modified, the OSD
display should be turned off.

Bit 5

HSEL

Description

0

The external Hsync signal is selected

(Initial value)

1

The internally generated Hsync signal is selected

Bit 4

Blank Bit: Cannot be read or modified.

Bit 3

Reserved: Cannot be modified and is always read as 0. When 1 is written to this bit,

correct operation is not guaranteed.

Bit 2

AFC Reset Control (ARST): Enables or disables the AFC reset function. When a VCR

motor skew occurs or the channel is switched, and if the Hsync signal (AFCH signal) output from
the AFC differs in phase from the reference Hsync signal input to the AFC, the AFC is reset to
eliminate the phase difference and to lock the AFCH signal phase to that of the reference signal.

Bit 2

ARST

Description

0

The reset function is disabled

(Initial value)

1

The reset function is enabled

Bits 1 and 0

Reserved: Cannot be modified and are always read as 0. When 1 is written to these

bits, correct operation is not guaranteed.

Summary of Contents for H8S/2196

























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for H8S/2196

Canon C50FSi - VB Network Camera Setup Manual preview
C50FSi - VB Network Camera
Brand: Canon Pages: 32
Rabbit 2000 Reference Manual preview
2000
Brand: Rabbit Pages: 120
Sun Microsystems Ray 3 Plus Client Getting Started Manual preview
Ray 3 Plus Client
Brand: Sun Microsystems Pages: 6
TC Electronic ATAC Service Manual preview
ATAC
Brand: TC Electronic Pages: 55
A10 Thunder Series Manual preview
Thunder Series
Brand: A10 Pages: 52
Stanwax Laser ILDA Gem Laser projector tool Instructions preview
ILDA Gem Laser projector tool
Brand: Stanwax Laser Pages: 3
Texas Instruments ThunderLAN TNETE100A Programmer'S Manual preview
ThunderLAN TNETE100A
Brand: Texas Instruments Pages: 179
AOpen VA1000 Lite2 User Manual And Technical Manual preview
VA1000 Lite2
Brand: AOpen Pages: 18
Multi-Link Power Stone Programming Manual preview
Power Stone
Brand: Multi-Link Pages: 31
MicroNova O047 Technical Installation Manual preview
O047
Brand: MicroNova Pages: 113
Cooler Master MCY-C3P1-KWNN Manual preview
MCY-C3P1-KWNN
Brand: Cooler Master Pages: 4
Parker Sporlan Division SCS-PB Series Installation And Operating Instructions Manual preview
Sporlan Division SCS-PB Series
Brand: Parker Pages: 10
Adaptec 2025ZCR - SCSI RAID Storage Controller Datasheet preview
2025ZCR - SCSI RAID Storage Controller
Brand: Adaptec Pages: 2
Panduit CDPP8RG-S Installation Instructions preview
CDPP8RG-S
Brand: Panduit Pages: 5
Sharp PN-ZB02 Installation Manual preview
PN-ZB02
Brand: Sharp Pages: 2
Sharp PN-ZB01 Installation Manual preview
PN-ZB01
Brand: Sharp Pages: 4
Sharp PN-L601B Brochure & Specs preview
PN-L601B
Brand: Sharp Pages: 4
Sharp PN-L601B Software Manual preview
PN-L601B
Brand: Sharp Pages: 163

Brands by name

Popular brands

Load more brands