manualshive.com logo in svg

Hitachi H8S/2196, Hardware Manual

The Hitachi H8S/2196 is a high-performance microcontroller designed for various hardware applications. To unlock its full potential, simply visit our website and download the free hardware manual. Find all the essential information you need to maximize your product experience at manualshive.com.

Share
Download
background image

Rev. 1.0, 02/00, page 353 of 1141

17.2.3

System Control Register (SYSCR)

7

—

0

—

6

—

0

—

5

INTM1

0

R

4

INTM0

0

R/W

3

XRST

1

R

0

—

1

—

2

—

0

—

1

—

0

—

Bit :

Initial value :

R/W : 

Only bit 3 is described here.  For details on functions not related to the watchdog timer, see
sections 3.2.2 and 6.2.1, System Control Register (SYSCR), and the descriptions of the relevant
modules.

Bit 3

External Reset (XRST): Indicates the reset source.  When the watchdog timer is used, a

reset can be generated by watchdog timer overflow in addition to external reset input.  XRST is a
read-only bit.  It is set to 1 by an external reset, and cleared to 0 by watchdog timer overflow.

Bit 3

XRST

Description

0

Reset is generated by watchdog timer overflow

1

Reset is generated by external reset input

(Initial value)

Summary of Contents for H8S/2196

























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for H8S/2196

Safety Vision ROADRECORDER 8000 User Manual preview
ROADRECORDER 8000
Brand: Safety Vision Pages: 40
EK-Quantum Momentum ROG Strix X570-E D-RGB User Manual preview
Momentum ROG Strix X570-E D-RGB
Brand: EK-Quantum Pages: 10
XNET INS2000 Install Manual preview
INS2000
Brand: XNET Pages: 17
VIA Technologies Mobile360 M810 Quick Start Manual preview
Mobile360 M810
Brand: VIA Technologies Pages: 25
ADTRAN Total Access 1500 Dual FXS/DPO Quick Start Manual preview
Total Access 1500 Dual FXS/DPO
Brand: ADTRAN Pages: 2
Renesas R8C/2F Quick Start Manual preview
R8C/2F
Brand: Renesas Pages: 6
Alcatel-Lucent Service Aggregation Router 7705 Installation Manual preview
Service Aggregation Router 7705
Brand: Alcatel-Lucent Pages: 20
Vivotek ND8212W Hardware Installation Manual preview
ND8212W
Brand: Vivotek Pages: 46
Netequalizer NE3000-10 Quick Start Manual preview
NE3000-10
Brand: Netequalizer Pages: 14
Vantec Aeroflow FX 120 VAF-1225 User Manual preview
Aeroflow FX 120 VAF-1225
Brand: Vantec Pages: 2
Digi NS7520B Series Hardware Reference Manual preview
NS7520B Series
Brand: Digi Pages: 339
Valcom VIP-997 Manual preview
VIP-997
Brand: Valcom Pages: 4
HighPoint NA381TB Quick Installation Manual preview
NA381TB
Brand: HighPoint Pages: 3
Actisense W2K-1 Install And User Manual preview
W2K-1
Brand: Actisense Pages: 14
MikroTik CCR2004-16G-2S+PC Quick Manual preview
CCR2004-16G-2S+PC
Brand: MikroTik Pages: 20
Billow MD01X User Manual preview
MD01X
Brand: Billow Pages: 31
Cisco Aironet 1430 Series Getting Started Manual preview
Aironet 1430 Series
Brand: Cisco Pages: 48
Cisco Aironet 1250 Series Manual preview
Aironet 1250 Series
Brand: Cisco Pages: 36

Brands by name

Popular brands

Load more brands