background image

 

 

APconnections, Inc. // 303.997.1300 // 

www.netequalizer.com

  

Page 1 of 14 

All rights reserved 

Copyright © 2010 to 2015 APconnections, Inc. 

rev. 20141125 

 

 

 

 

Quick Start Guide 

 

Table of Contents 

Factory Default IP Settings ................................................................................................................................ 2

 

Installing the NetEqualizer ................................................................................................................................ 2

 

Step #1: Cabling the NetEqualizer into your Network .................................................................................................. 2

 

Step #2: Configuring the NetEqualizer ......................................................................................................................... 4

 

Step #3: Setting Up Equalizing ..................................................................................................................................... 8

 

Step #4: Controlling Peer-to-peer Traffic (P2P) ...........................................................................................................10

 

Step #5: Validating & Backing Up Your Configuration .................................................................................................11

 

Appendix #1: Viewing Traffic ......................................................................................................................................12

 

Appendix #2: Troubleshooting your Setup ..................................................................................................................13

 

Appendix #3: Syncing NetEqualizer Date/Time ...........................................................................................................14

 

 

***Usernames & passwords are xxx'd out in this Demo Quick Start Guide.*** 

 

Author’s Note: 

Congratulations on your NetEqualizer purchase!  You are now on your way to achieving "Faster Networks, with Zero 
Maintenance, at the Best Prices".  In fact, many network administrators find that they can set-up and configure a 
NetEqualizer on their network in one (1) hour or less.  
 
However, if you have any questions that you need help with during your install, our Support Team is here to help you.  
Please call Support at 303.997.1300 x102 or send an email to 

[email protected]

 
After you have completed your installation, if you would like a 

complimentary review of your NetEqualizer 

configuration

Click on -> 

Troubleshooting and Support 

-> 

Troubleshooting 

->

 

[

Run Diagnostics

]

 ->

 

[

Run 

Diagnostics

]

.  Save the results as a .txt file, email as an attachment (otherwise email will cut off content) to 

[email protected]

.  We would be happy to verify that you have optimized setup for your network. 

 
 

Summary of Contents for NE3000-10















Reviews: