Mazda MX-5 Miata Sport 2007 Скачать руководство пользователя страница 2107

Страница: 2107 / 2244

1. Remove the sealant along the perimeter of the glass using a cutting a razor. (When reusing the glass)

2. Clean and degrease an

approx. 50 mm {2.0 in}

wide strip along the perimeter of the windshield.

3. Inspect the glass for cracks. If it is cracked, chamfer it using sandpaper.

4. Align the marks made before removal and install the pin to the windshield referring to the figure. (when

reusing the glass, and the pin was removed)

Fig. 31: Positions For Installing Pin To Windshield

Courtesy of MAZDA MOTORS CORP.

5. Install the windshield molding.

6. Use glass primer on the glass, then allow it to dry for

approx. 30 min.

Fig. 32: Identifying Windshield Molding

Courtesy of MAZDA MOTORS CORP.

CAUTION:



To prevent weakening of the primer adhesion, keep the bonding
surface free of dirt, moisture, and grease. Do not touch the
surface with your hand.

NOTE:



Make sure to apply primer to the hollowed marks in the ceramic
coating.

2007 Mazda MX-5 Miata Sport

2007 ACCESSORIES & BODY, CAB Glass/Windows/Mirrors - MX-5 Miata

Microsoft

Thursday, July 09, 2009 3:24:31 PM

Page 22

«
...
2105
2106
2107
2108
2109
...
»

Содержание MX-5 Miata Sport 2007





































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание MX-5 Miata Sport 2007

Отзывы:

Похожие инструкции для MX-5 Miata Sport 2007

Бренды по названию

Популярные бренды

Mazda MX-5 Miata Sport 2007, Руководство пользователя

Результаты поиска

Содержание MX-5 Miata Sport 2007

Отзывы:

Похожие инструкции для MX-5 Miata Sport 2007

Бренды по названию

Популярные бренды