manualshive.com logo in svg

Mazda MX-5 Miata Sport 2007, Руководство пользователя, Страница: 1401 / 2244

Поделиться
Скачать
Mazda MX-5 Miata Sport 2007 Скачать руководство пользователя страница 1401

5. Disconnect from A/C unit in the order in 

Fig. 2

 . 

Fig. 2: Disconnect A/C Unit Pipe Lines (With Torque Specifications)

 

Courtesy of MAZDA MOTORS CORP.

 

6. Remove the following parts: 

1. Console (See 

CONSOLE REMOVAL/INSTALLATION

 .)  

2. Glove compartment (See 

GLOVE COMPARTMENT REMOVAL/INSTALLATION

 .)  

3. Side wall (See 

SIDE WALL REMOVAL/INSTALLATION

 .)  

4. Console panel (See 

CONSOLE PANEL REMOVAL/INSTALLATION

 .)  

5. Center panel unit (See 

CENTER PANEL UNIT REMOVAL/INSTALLATION

 .)  

6. Lower panel (See 

LOWER PANEL REMOVAL/INSTALLATION

 .)  

7. Knee bolster  

CAUTION:

If moisture or foreign material enters the refrigeration cycle, 
cooling ability will be lowered and abnormal noise or other 
malfunction could occur. Always plug open fittings immediately 
after removing any refrigeration cycle parts.  

 

2007 Mazda MX-5 Miata Sport 

2007 HVAC Basic System - MX-5 Miata

  

Microsoft 

 

Thursday, July 09, 2009 2:22:45 PM

Page 2 

© 2005 Mitchell Repair Information Company, LLC. 

Содержание MX-5 Miata Sport 2007





































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов