Mazda MX-5 Miata Sport 2007 Скачать руководство пользователя страница 1605 | Manualshive

Страница: 1605 / 2244

background image

4

(Method for registering other
keys using two keys that can
start the engine is disabled.)

possible to register
additional keys
according to
procedure No.1. The
system can be
returned to the
original setting. The
M-MDS must always
be used to change the
system setting.

4

Changing the method for
registering additional keys.
(Method for registering other
keys using two keys that can
start the engine is enabled.)



M-MDS



This is the default
setting on new
vehicles.

5

Replacing the instrument cluster.



Replacement
instrument cluster



Registration keys
(two or more)



M-MDS



Unless keys are
registered after
replacing the steering
lock, the engine
cannot be started.
Before beginning the
procedure, verify that
the customer has
turned in all of the
keys for the vehicle.



Unless two or more
keys are registered
after replacement, the
engine cannot be
started.



The keys (two or
more keys) readied
before beginning the
procedure do not have
to be new keys. Any
key that is capable of
starting the engine
before beginning the
procedure can be
used.

5

Replacing the PCM.



Replacement PCM



M-MDS

-

Replacing the PCM and
instrument cluster.



Replacement PCM



Replacement
instrument cluster



Unless keys are
registered after
replacing the steering

2007 Mazda MX-5 Miata Sport

2007 ACCESSORIES & BODY, CAB Security and Locks (Keyless Entry System) - MX-5 Miata

Microsoft

Thursday, July 09, 2009 3:35:24 PM

Page 6

© 2005 Mitchell Repair Information Company, LLC.

«
...
1603
1604
1605
1606
1607
...
»

Содержание MX-5 Miata Sport 2007





































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для MX-5 Miata Sport 2007

Бренд: U.S. General Страницы: 5

Бренд: UnderCover Страницы: 16

Бренд: Jeda Страницы: 8

Бренд: Jeep Страницы: 496

KO PROPO RTF 2002 ESC

Бренд: Tamiya Страницы: 2

Cherokee 16 1982

Бренд: Jeep Страницы: 1311

Бренд: Ultra-tow Страницы: 14

Бренд: Mercedes-Benz Страницы: 121

Бренд: Menabo Страницы: 8

Бренд: Camtree Страницы: 5

Бренд: Cadillac Страницы: 409

Бренд: Fortin Страницы: 9

Бренд: Bestop Страницы: 4

Бренд: true-i Страницы: 11

Бренд: Honda Страницы: 4

Бренд: Pet Gear Страницы: 4

Бренд: TOP VEHICLE TECH Страницы: 8

Бренд: Prime Design Страницы: 12

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды