Mazda MX-5 Miata Sport 2007 Скачать руководство пользователя страница 1092

Страница: 1092 / 2244

Fig. 24: Holding Exhaust Camshaft Using Wrench On Case Hexagon

Courtesy of MAZDA MOTORS CORP.

32. Tighten the exhaust camshaft sprocket lock bolt.

Tightening torque

69-75 N.m {7.1-7.6 kgf.m, 50.9-55.3 ft.lbf}

33. Remove the

SST

from the camshaft.

34. Remove the

SST

from the block lower blind plug.

35. Rotate the crankshaft clockwise two turns until the TDC position.



If not aligned, loosen the crankshaft pulley lock bolt and repeat from Step 16.

36. Apply silicone sealant to the engine front cover upper blind plug.

37. Install the engine front cover upper blind plug.

Tightening torque

8.0-11.5 N.m {82-117 kgf.cm, 71-101 ft.lbf}

2007 Mazda MX-5 Miata Sport

2007 ENGINE Mechanical - MX-5

Microsoft

Thursday, July 09, 2009 3:21:50 PM

Page 26

«
...
1090
1091
1092
1093
1094
...
»

Содержание MX-5 Miata Sport 2007





































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание MX-5 Miata Sport 2007

Отзывы:

Mazda MX-5 Miata Sport 2007, Руководство пользователя, Страница: 1092 / 2244

Результаты поиска

Содержание MX-5 Miata Sport 2007

Отзывы: