Mazda MX-5 Miata Sport 2007 Скачать руководство пользователя страница 1509

Страница: 1509 / 2244

Check Code 28

CHECK CODE 28

CONDITION

DISPLAY

ACTION

Select check code

26.



Display is normal.



Warning and indicator
light illuminated.



Generator
warning light



AT warning light



DSC indicator
light



DSC OFF light



ABS warning
light



Brake system
warning light



Selector indicator
light



MIL



Cruise set
indicator light



Cruise main
indicator light



Security light



Keyless warning
light



Keyless indicator
light



The odometer/tripmeter
is normal.



Warning and indicator
is normal.

Except above

Replace the instrument
cluster.

Check code 28 Oil pressure gauge operation signal

INSPECTION

CONDITION

DISPLAY

ACTION

After selecting

check code 28,

The oil pressure gauge

indicates status in the

following order

approx.

every 2 s.



H --> Center --> L -->

H (fixed)

The oil pressure gauge is
normal.

2007 Mazda MX-5 Miata Sport

2007 ACCESSORIES & BODY, CAB Instrumentation-Driver Info - MX-5 Miata

Microsoft

Thursday, July 09, 2009 3:30:27 PM

Page 21

«
...
1507
1508
1509
1510
1511
...
»

Содержание MX-5 Miata Sport 2007





































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание MX-5 Miata Sport 2007

Отзывы:

Похожие инструкции для MX-5 Miata Sport 2007

Бренды по названию

Популярные бренды

Mazda MX-5 Miata Sport 2007, Руководство пользователя

Результаты поиска

Содержание MX-5 Miata Sport 2007

Отзывы:

Похожие инструкции для MX-5 Miata Sport 2007

Бренды по названию

Популярные бренды