Mazda MX-5 Miata Sport 2007 Скачать руководство пользователя страница 2092

Страница: 2092 / 2244

Fig. 10: Identifying Glass Stopper With Bolt With Torque Specifications

Courtesy of MAZDA MOTORS CORP.

DOOR QUARTER GLASS REMOVAL/INSTALLATION

1. Position the door glass so that the distance between the top of the front door glass and top of the front

beltline molding is

110 mm {4.33 in}.

2. Remove the battery cover.

3. Disconnect the negative battery cable.(See

BATTERY REMOVAL/INSTALLATION [LF]

4. Remove the door trim.(See

DOOR TRIM REMOVAL/INSTALLATION

5. Remove the door unit.(See

DOOR UNIT REMOVAL/INSTALLATION

6. Remove the door glass.(See

DOOR GLASS REMOVAL/INSTALLATION

7. Remove the power window regulator.(See

POWER WINDOW REGULATOR

REMOVAL/INSTALLATION

8. Remove the nut and bolt, then remove the door glass guide.(See

DOOR GLASS GUIDE

INSTALLATION NOTE

Fig. 11: Identifying Distance Between Top Of Front Door Glass & Top Of Front Belt Line Molding
Courtesy of MAZDA MOTORS CORP.

2007 Mazda MX-5 Miata Sport

2007 ACCESSORIES & BODY, CAB Glass/Windows/Mirrors - MX-5 Miata

Microsoft

Thursday, July 09, 2009 3:24:31 PM

Page 7

«
...
2090
2091
2092
2093
2094
...
»

Содержание MX-5 Miata Sport 2007





































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание MX-5 Miata Sport 2007

Отзывы:

Похожие инструкции для MX-5 Miata Sport 2007

Бренды по названию

Популярные бренды

Mazda MX-5 Miata Sport 2007, Руководство пользователя

Результаты поиска

Содержание MX-5 Miata Sport 2007

Отзывы:

Похожие инструкции для MX-5 Miata Sport 2007

Бренды по названию

Популярные бренды