Mazda MX-5 Miata Sport 2007 Скачать руководство пользователя страница 1258

Страница: 1258 / 2244

Courtesy of MAZDA MOTORS CORP.

DECK PANEL LINK REMOVAL NOTE

1. When removing the deck panel link, place the positioning mark by affixing masking tape on the deck

panel link and deck panel.

DECK PANEL LINK INSTALLATION NOTE

1. Install the shim according to the number verified prior to removal.

2. Align the alignment marks placed before the deck panel link removal and install the deck panel link.

3. Refer to

DECK PANEL ADJUSTMENT

and verify that the gap and height difference between the deck

panel, trunk lid, and back window glass are within the specifications. Adjust the power retractable
hardtop if necessary.

DECK PANEL ADJUSTMENT

1. Loosen the installation nuts for deck panel.

2. Adjust the gap and height difference between the deck panel and trunk lid within the specification by

moving the deck panel back and forth, left and right, and by adjusting the number of shims if necessary.

Fig. 80: Identifying Deck Panel, Deck Panel Link And Nut With Torque Specifications

Courtesy of MAZDA MOTORS CORP.

2007 Mazda MX-5 Miata Sport

2007 ACCESSORIES & BODY, CAB Exterior Trim - MX-5 Miata

Microsoft

Thursday, July 09, 2009 3:32:13 PM

Page 58

«
...
1256
1257
1258
1259
1260
...
»

Содержание MX-5 Miata Sport 2007





































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание MX-5 Miata Sport 2007

Отзывы:

Похожие инструкции для MX-5 Miata Sport 2007

Бренды по названию

Популярные бренды

Mazda MX-5 Miata Sport 2007, Руководство пользователя

Результаты поиска

Содержание MX-5 Miata Sport 2007

Отзывы:

Похожие инструкции для MX-5 Miata Sport 2007

Бренды по названию

Популярные бренды