Mazda MX-5 Miata Sport 2007 Скачать руководство пользователя страница 655

Страница: 655 / 2244

Fig. 49: Exploded View Of Caliper (Rear) (With Torque Specifications)

Courtesy of MAZDA MOTORS CORP.

2. Assemble in the reverse order of disassembly.

PISTON DISASSEMBLY NOTE

1. Rotate the piston counter-clockwise using the

SST

, remove the piston from the caliper body.

Fig. 50: Rotating Piston Counter-Clockwise Using SST

Courtesy of MAZDA MOTORS CORP.

DUST SEAL, PISTON ASSEMBLY NOTE

1. Assemble the dust seal to the piston.

2. Assemble the lip of the dust seal to the groove of the caliper body with the dust seal is assembled to the

piston as shown in

Fig. 51

2007 Mazda MX-5 Miata Sport

2007 BRAKES Conventional Brake System - MX-5 Miata

Microsoft

Thursday, July 09, 2009 3:18:52 PM

Page 55

Содержание MX-5 Miata Sport 2007





































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание MX-5 Miata Sport 2007

Отзывы:

Похожие инструкции для MX-5 Miata Sport 2007

Бренды по названию

Популярные бренды

Mazda MX-5 Miata Sport 2007, Руководство пользователя

Результаты поиска

Содержание MX-5 Miata Sport 2007

Отзывы:

Похожие инструкции для MX-5 Miata Sport 2007

Бренды по названию

Популярные бренды