Mazda MX-5 Miata Sport 2007 Скачать руководство пользователя страница 1368 | Manualshive

Страница: 1368 / 2244

background image

FUEL PUMP UNIT INSPECTION [LF]

FUEL PUMP OPERATION INSPECTION

1. Follow "BEFORE SERVICE PRECAUTION" before performing any work operations to prevent fuel

from spilling from the fuel system. (See

BEFORE SERVICE PRECAUTION [LF]

.)

2. Remove the fuel-filler cap.

3. Start the fuel pump using the following procedure:

Using M-MDS

1. Connect the M-MDS to the DLC-2.

WARNING:



Fuel is very flammable liquid. If fuel spills or leaks from the
pressurized fuel system, it will cause serious injury or death and
facility breakage. Fuel can also irritate skin and eyes. To prevent
this, always complete the "

FUEL LINE SAFETY PROCEDURE

", while

referring to BEFORE SERVICE PRECAUTION [LF] .



Fuel is very flammable liquid. If fuel spills or leaks from the
pressurized fuel system, it will cause serious injury or death and
facility breakage. Fuel can also irritate skin and eyes. To prevent
this, before performing the fuel pump unit removal/installation,
always complete the "Fuel Leak Inspection After Fuel Pump Unit
Installation".



A person charged with static electricity could cause a fire or
explosion, resulting in death or serious injury. Before draining fuel,
make sure to discharge static electricity by touching the vehicle
body.

2007 Mazda MX-5 Miata Sport

2007 ENGINE Fuel System - MX-5 Miata

Microsoft

Thursday, July 09, 2009 2:37:12 PM

Page 27

© 2005 Mitchell Repair Information Company, LLC.

«
...
1366
1367
1368
1369
1370
...
»

Содержание MX-5 Miata Sport 2007





































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для MX-5 Miata Sport 2007

Бренд: Yakima Страницы: 11

Бренд: Conrad Страницы: 26

2003 Thunderbird

Бренд: Ford Страницы: 200

10-8002-C11998B

Бренд: Saleen Страницы: 12

2013 Buick Verano

Бренд: Buick Страницы: 5

Бренд: Whispbar Страницы: 15

Бренд: Cadillac Страницы: 368

Бренд: Luverne Страницы: 3

Бренд: Navman Страницы: 27

Calispace Ocean 80

Бренд: Calitop Страницы: 5

Бренд: Cadillac Страницы: 335

Бренд: Volvo Страницы: 92

Бренд: ECS Electronics Страницы: 42

OVER DRIVE PolyPRO 3 Car Cover

Бренд: Classic Accessories Страницы: 2

Бренд: Kargo Master Страницы: 18

Бренд: Front Runner Страницы: 7

Бренд: KAP Страницы: 22

2002 Accord Coupe

Бренд: Honda Страницы: 367

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды