Mazda MX-5 Miata Sport 2007 Скачать руководство пользователя страница 252 | Manualshive

Страница: 252 / 2244

background image

1. Connect the WDS or equivalent to the DLC-2 (16-pin).

Fig. 25: Identifying DLC-2 Location

Courtesy of MAZDA MOTORS CORP.

2. Select "Body" from the menu.

3. Select "Restraints".

4. Select "Seat Weight Sensor ReZero Procedure".

5. Perform inspection following the procedures on the WDS or equivalent screen.

sensor inspection using the WDS or equivalent.



Removal of the passenger-side seat



Loosening and retightening of passenger's seat fixing bolts



Or, the vehicle is involved in a collision



If any of the following work is performed, perform the seat weight
sensor calibration using the WDS or equivalent. (See SEAT WEIGHT
SENSOR CALIBRATION .)



Replacement with a new seat weight sensor



Replacement with a new seat weight sensor control module



Replacement with new passenger-side seat parts



Disassembly of the passenger-side seat

2008 Mazda MX-5 Miata Grand Touring

2008 RESTRAINTS Air Bag System - MX-5 Miata

Microsoft

Thursday, July 09, 2009 3:43:37 PM

Page 28

© 2005 Mitchell Repair Information Company, LLC.

«
...
250
251
252
253
254
...
»

Содержание MX-5 Miata Sport 2007





































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для MX-5 Miata Sport 2007

Бренд: Jeep Страницы: 322

Бренд: Jeep Страницы: 341

Бренд: Jeep Страницы: 310

Бренд: Jeep Страницы: 189

Бренд: Jeep Страницы: 26

Бренд: Jeep Страницы: 21

Бренд: TATA Motors Страницы: 156

Бренд: Tessera4x4 Страницы: 20

Бренд: PEUGEOT Страницы: 249

Бренд: U.S. General Страницы: 8

Бренд: Beper Страницы: 52

Бренд: TAUBENREUTHER Страницы: 18

Бренд: Cadillac Страницы: 2

Бренд: Buick Страницы: 20

Бренд: Whispbar Страницы: 14

Бренд: Meritor Страницы: 20

SB-J-GCHER2/10W3v2

Бренд: Stealthbox Страницы: 2

Бренд: Suzuki Страницы: 504

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды