Mazda MX-5 Miata Sport 2007 Скачать руководство пользователя страница 373 | Manualshive

Страница: 373 / 2244

background image

Fig. 72: Identifying Activation Switch

Courtesy of MAZDA MOTORS CORP.

AIR BAG MODULE AND PRE-TENSIONER SEAT BELT DISPOSAL
PROCEDURES

WARNING:



A live (undeployed) air bag module or pre-tensioner seat belt may
accidentally operate (deploy) when it is disposed of and cause
serious injury. Always refer to the AIR BAG MODULE AND PRE-
TENSIONER SEAT BELT DEPLOYMENT PROCEDURES and dispose
of air bag modules and pre-tensioner seat belts in a deployed
condition.



The air bag modules and the pre-tensioner seat belts are very hot
immediately after they are deployed. You can be burned. Do not
touch an air bag module and pre-tensioner seat belt for at least 15
min after deployment.



Pouring water on the deployed air bag module and pre-tensioner
seat belt is dangerous. The water will mix with the residual gases to
form a gas that can make breathing difficult. Do not pour water on
the deployed air bag module and pre-tensioner seat belt.



The deployed air bag module or pre-tensioner seat belt may contain
deposits of sodium hydroxide, a caustic byproduct of the gas-
generated combustion. If this substance gets into your eyes or on
your hands, it can cause irritation and itching. When handling the

2007 Mazda MX-5 Miata Sport

2007 RESTRAINTS Air Bag System - MX-5 Miata

Microsoft

Thursday, July 09, 2009 2:12:56 PM

Page 73

© 2005 Mitchell Repair Information Company, LLC.

«
...
371
372
373
374
375
...
»

Содержание MX-5 Miata Sport 2007





































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для MX-5 Miata Sport 2007

Бренд: Ignition Страницы: 1

Бренд: Whispbar Страницы: 16

Бренд: Hama Страницы: 40

Бренд: T-Mobile Страницы: 2

JEEP GL ADIATOR JT TOPPER ROOF RACK

Бренд: JCROffroad Страницы: 7

IVH-9000-2R440Q

Бренд: Vecow Страницы: 110

Бренд: Jaeger Страницы: 13

Бренд: Billien Страницы: 2

Бренд: Lexus Страницы: 28

Бренд: Curt Group Страницы: 3

Бренд: Juna Страницы: 10

Бренд: Cadillac Страницы: 48

2001 Accord Sedan

Бренд: Honda Страницы: 372

Бренд: Imiola HAK-POL Страницы: 3

Pro Competition

Бренд: G-Tech Страницы: 180

Бренд: Curt Manufacturing Страницы: 4

Бренд: Hama Страницы: 2

MagicWatch MWE850

Бренд: Waeco Страницы: 200

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды