Mazda MX-5 Miata Sport 2007 Скачать руководство пользователя страница 1604 | Manualshive

Страница: 1604 / 2244

background image

case, perform
procedure No.2

2

Making a spare key when the
customer has one key that can
start the engine or no keys. Or
registering an additional key.



Registration key



M-MDS

-

3

Clearing previously registered
key ID numbers.



Registration keys
(two or more)



M-MDS



All the key ID
numbers registered in
the vehicle will be
cleared.



Unless keys are re-
registered after
clearing the key ID
numbers, the engine
cannot be started.
Before beginning the
procedure, verify that
the customer has
turned in all of the
keys for the vehicle.



Unless two or more
keys are registered
after replacement, the
engine cannot be
started.



The keys (two or
more keys) readied
before beginning the
procedure do not have
to be new keys. Any
key that is capable of
starting the engine
before beginning the
procedure can be
used.

3

Replace all the keys. (Key
cylinder replacement)



Registration keys
(two or more)



M-MDS



When replacing the
key cylinder, have
two or more keys
ready for registration
before beginning the
procedure, since the
previous keys will be
invalid.

Changing the method for
registering additional keys.



M-MDS



After performing this
procedure it is not

2007 Mazda MX-5 Miata Sport

2007 ACCESSORIES & BODY, CAB Security and Locks (Keyless Entry System) - MX-5 Miata

Microsoft

Thursday, July 09, 2009 3:35:24 PM

Page 5

© 2005 Mitchell Repair Information Company, LLC.

«
...
1602
1603
1604
1605
1606
...
»

Содержание MX-5 Miata Sport 2007





































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для MX-5 Miata Sport 2007

Бренд: Federal Signal Corporation Страницы: 13

Бренд: AAMP of America Страницы: 6

Бренд: Jeep Страницы: 12

Бренд: Jeep Страницы: 6

Бренд: APEXi Страницы: 18

Бренд: Prorack Страницы: 15

Бренд: Thule Страницы: 12

Бренд: hc-cargo Страницы: 60

Бренд: Saab Страницы: 12

Бренд: FALCON RIDGE Страницы: 7

Бренд: Volvo Страницы: 30

JEEP GL ADIATOR JT TOPPER ROOF RACK

Бренд: JCROffroad Страницы: 7

IVH-9000-2R440Q

Бренд: Vecow Страницы: 110

Бренд: Volvo Страницы: 42

Бренд: EUFAB Страницы: 4

Omni-Bike Sport Ducato

Бренд: OMNISTOR Страницы: 5

Бренд: Magneti Marelli Страницы: 3

Бренд: HUSKY LINERS Страницы: 4

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды