Mazda MX-5 Miata Sport 2007 Скачать руководство пользователя страница 649

Страница: 649 / 2244

Fig. 44: Identifying Wheel Hub & Disc Plate Mark

Courtesy of MAZDA MOTORS CORP.

DISC PLATE INSTALLATION NOTE

1. Remove any rust or foreign material from the wheel hub and disc plate.

2. Align the marks made before removal and install the disc plate to the wheel hub.

CALIPER INSTALLATION NOTE

1. Clean the exposed area of the piston.

2. Rotate the piston clockwise slowly using the

SST

and push the piston completely until the piston grooves

are in the position shown in

Fig. 45

3. Install the caliper.

2007 Mazda MX-5 Miata Sport

2007 BRAKES Conventional Brake System - MX-5 Miata

Microsoft

Thursday, July 09, 2009 3:18:52 PM

Page 49

Содержание MX-5 Miata Sport 2007





































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание MX-5 Miata Sport 2007

Отзывы:

Mazda MX-5 Miata Sport 2007, Руководство пользователя, Страница: 649 / 2244

Результаты поиска

Содержание MX-5 Miata Sport 2007

Отзывы: