Mazda MX-5 Miata Sport 2007 Скачать руководство пользователя страница 55 | Manualshive

Страница: 55 / 2244

background image

single unit.

Connecting rod side clearance (Standard)

0.14-0.36 mm {0.0056-0.0141 in}

Connecting rod side clearance (Maximum)

0.435 mm {0.0172 in}

Fig. 55: Measuring Connecting Rod Large End Side Clearance

Courtesy of MAZDA MOTORS CORP.

3. Remove the connecting rod cap.

4. Position plastigage atop the journals in the axial direction.

5. Install the connecting rod bearing and connecting rod cap. (See

CONNECTING ROD CAP

ASSEMBLY NOTE

).

6. Remove the connecting rod cap.

7. Measure the connecting rod oil clearance.



If it exceeds the specification, replace the connecting rod bearing or grind the crank pin and use
oversize bearings so that the specified clearance is obtained.

Connecting rod bearing oil clearance (Standard)

2007 Mazda MX-5 Miata Sport

2006-08 ENGINE Mechanical - Overhaul - 2.0L (LF) & 2.3L (L3) - Mazda6 & MX-5 Miata

Microsoft

Thursday, July 09, 2009 2:43:25 PM

Page 55

© 2005 Mitchell Repair Information Company, LLC.

«
...
53
54
55
56
57
...
»

Содержание MX-5 Miata Sport 2007





































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для MX-5 Miata Sport 2007

Бренд: Toyota Страницы: 529

2007 MazdaSpeed6

Бренд: Mazda Страницы: 12

Бренд: MAXWORKS Страницы: 7

Бренд: Skoda Страницы: 165

Бренд: Yakima Страницы: 12

Бренд: Axxess Страницы: 16

Бренд: APS Страницы: 3

Бренд: Discount Car Stereo Страницы: 8

Бренд: Honda Страницы: 24

Бренд: Acura Страницы: 7

Бренд: Yenkee Страницы: 22

Бренд: SkyRack Страницы: 2

Directechs FORD11

Бренд: Directed Страницы: 23

Бренд: Whispbar Страницы: 15

Бренд: Ranger design Страницы: 6

Бренд: Jeep Страницы: 52

Бренд: Maserati Страницы: 288

2009 Highlander

Бренд: Toyota Страницы: 19

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды