Mazda MX-5 Miata Sport 2007 Скачать руководство пользователя страница 295

Страница: 295 / 2244

Fig. 70: Tying Tires Together With Wire

Courtesy of MAZDA MOTORS CORP.

6. Connect the

SST

(Deployment tool) to the

SST

(Adapter harness).

7. Connect the

SST

(Deployment tool) to the battery. Connect the power supply red clip to the positive

battery terminal, and the black clip to the negative battery terminal.

8. Verify that the red lamp on the

SST

(Deployment tool) is illuminated.

9. Verify that all persons are standing

at least 6 m {20 ft}

away from the vehicle.

2008 Mazda MX-5 Miata Grand Touring

2008 RESTRAINTS Air Bag System - MX-5 Miata

Microsoft

Thursday, July 09, 2009 3:43:37 PM

Page 71

Содержание MX-5 Miata Sport 2007





































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание MX-5 Miata Sport 2007

Отзывы:

Похожие инструкции для MX-5 Miata Sport 2007

Бренды по названию

Популярные бренды

Mazda MX-5 Miata Sport 2007, Руководство пользователя

Результаты поиска

Содержание MX-5 Miata Sport 2007

Отзывы:

Похожие инструкции для MX-5 Miata Sport 2007

Бренды по названию

Популярные бренды