Mazda MX-5 Miata Sport 2007 Скачать руководство пользователя страница 703

Страница: 703 / 2244

Fig. 16: Identifying Clutch Unit Components (With Torque Specifications)
Courtesy of MAZDA MOTORS CORP.

CLUTCH COVER AND DISC REMOVAL NOTE

1. Install the

SSTs.

2. Loosen each bolt one turn at a time in a crisscross pattern until spring tension is released.

3. Remove the clutch cover and disc.

Fig. 17: Identifying SSTs

Courtesy of MAZDA MOTORS CORP.

PILOT BEARING REMOVAL NOTE

1. Use the

SST

to remove the pilot bearing.

NOTE:



The pilot bearing does not need to be removed unless you are replacing it.

2007 Mazda MX-5 Miata Sport

2007 TRANSMISSION Clutch - MX-5 Miata

Microsoft

Thursday, July 09, 2009 1:44:46 PM

Page 19

Содержание MX-5 Miata Sport 2007





































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание MX-5 Miata Sport 2007

Отзывы:

Mazda MX-5 Miata Sport 2007, Руководство пользователя, Страница: 703 / 2244

Результаты поиска

Содержание MX-5 Miata Sport 2007

Отзывы: