Mazda MX-5 Miata Sport 2007 Скачать руководство пользователя страница 635

Страница: 635 / 2244

Fig. 31: Measuring Front Disc Plate Runout

Courtesy of MAZDA MOTORS CORP.

Thickness Variation Inspection

1. Clean the disc plate-to-pad friction surface using a brake cleaner.

2. Measure the points indicated in

Fig. 32

using a caliper (micrometer).

3. Subtract the minimum value from the maximum, and if the result is not within specification, machine the

disc plate using a lathe.

Thickness variation limit

0.015 mm {0.00059 in}

WARNING:



Do not exceed minimum disc plate thickness.

2007 Mazda MX-5 Miata Sport

2007 BRAKES Conventional Brake System - MX-5 Miata

Microsoft

Thursday, July 09, 2009 3:18:52 PM

Page 35

Содержание MX-5 Miata Sport 2007





































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание MX-5 Miata Sport 2007

Отзывы:

Похожие инструкции для MX-5 Miata Sport 2007

Бренды по названию

Популярные бренды

Mazda MX-5 Miata Sport 2007, Руководство пользователя

Результаты поиска

Содержание MX-5 Miata Sport 2007

Отзывы:

Похожие инструкции для MX-5 Miata Sport 2007

Бренды по названию

Популярные бренды