Mazda MX-5 Miata Sport 2007 Скачать руководство пользователя страница 1482

Страница: 1482 / 2244

DIAGNOSTIC PROCEDURE

NO. 7 SPEEDOMETER INDICATION IS DEFECTIVE

SPEEDOMETER INDICATION IS DEFECTIVE POSSIBLE CAUSE TABLE

STEP

INSPECTION

ACTION



Turn the light switch to the TNS position.



Does the instrument cluster illumination
turn on?

Yes Troubleshooting completed.

Go to the next step.



Does the non-illumination include the entire
instrument cluster?

Yes Go to the next step.

Replace the instrument cluster.



Inspect the ROOM and ILLUMI fuse.



Are the fuses normal?

Yes Go to the next step.

Replace the fuse.



If the fuse is melted, inspect the

wiring harness for short to ground.

Repair or replace the wiring harness,

then replace the fuse.



Turn the ignition switch off.



Inspect the instrument cluster connector
terminals for poor connection (such as
damaged/pulled-out pins, and corrosion).



Are the terminals normal?

Yes Replace the instrument cluster.

Repair or replace the terminal.

Speedometer indication is defective

POSSIBLE CAUSE



ABS HU/CM or DSC HU/CM malfunction



PCM malfunction



Instrument cluster malfunction



Connector or pin malfunction



Short circuit in wiring harness between CAN-L, CAN-H and GND



Open circuit in CAN wiring harness (CAN-L, CAN-H)



CAN wiring harness (CAN-L, CAN-H) short each other

2007 Mazda MX-5 Miata Sport

2007 ACCESSORIES & BODY, CAB Symptom Troubleshooting (Instrument Cluster) - MX-5 Miata

Microsoft

Thursday, July 09, 2009 3:31:09 PM

Page 10

«
...
1480
1481
1482
1483
1484
...
»

Содержание MX-5 Miata Sport 2007





































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание MX-5 Miata Sport 2007

Отзывы:

Похожие инструкции для MX-5 Miata Sport 2007

Бренды по названию

Популярные бренды

Mazda MX-5 Miata Sport 2007, Руководство пользователя

Результаты поиска

Содержание MX-5 Miata Sport 2007

Отзывы:

Похожие инструкции для MX-5 Miata Sport 2007

Бренды по названию

Популярные бренды