Mazda MX-5 Miata Sport 2007 Скачать руководство пользователя страница 2004 | Manualshive

Страница: 2004 / 2244

background image

contamination,
winter/summer
blend) Are all
items normal?

2

Connect the M-MDS or
equivalent to the DLC-
2. Turn the ignition
switch to the ON
position (Engine off).
Retrieve any DTCs.
Are there any DTCs
displayed?

Yes

DTC is displayed:

Go to the appropriate DTC
inspection.
(See

DTC TABLE [LF]

.)

No

DTC is displayed:

Go to the next step.

3

Is the engine
overheating?

Yes

Go to symptom troubleshooting

NO.17 COOLING SYSTEM
CONCERNS-
OVERHEATING [LF]

.

No

Go to the next step.

4

Connect the M-MDS or
equivalent to the DLC-
2.
Access APP1, APP2,
RPM, MAF, TP, IAT
and VSS PIDs.
Drive vehicle while
monitoring PIDs.
Are PIDs within
specifications?
(See

PCM

INSPECTION [LF]

.)

Yes

Go to the next step.

No

APP1, APP2 PIDs:

Inspect if output signal
accelerator pedal position sensor
changes smoothly.

RPM PID:

Inspect CKP sensor and related
wiring harness for vibration or
intermittent open/short circuit or
both.

MAF PID:

Inspect for intermittent open
circuit of MAF sensor and
related wiring harness.

TP PID:

Inspect if output signal TP
sensor changes smoothly.

IAT PID:

Inspect for air suction in intake-
air system.
If normal, inspect intermittent
short circuit of IAT sensor and
related wiring harnesses.

VSS PID:

Inspect for intermittent open
circuit of VSS and related
wiring harness.

5

Visually inspect the
CKP sensor and teeth of

Yes

Go to the next step.

2007 Mazda MX-5 Miata Sport

2007 ENGINE PERFORMANCE Symptom Troubleshooting - MX-5 Miata

Microsoft

Thursday, July 09, 2009 2:42:10 PM

Page 71

© 2005 Mitchell Repair Information Company, LLC.

«
...
2002
2003
2004
2005
2006
...
»

Содержание MX-5 Miata Sport 2007





































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для MX-5 Miata Sport 2007

Бренд: Federal Signal Corporation Страницы: 8

Бренд: Federal Signal Corporation Страницы: 8

Бренд: Mobile Create Страницы: 15

LeisureWize EMOVE EM303A

Бренд: Streetwize Страницы: 20

Бренд: Xblitz Страницы: 30

DELTA DL FIX 209FP

Бренд: Menabo Страницы: 8

Бренд: Yutrax Страницы: 8

Бренд: Flash Cover Страницы: 2

Бренд: Porsche Страницы: 98

Бренд: Draw tite Страницы: 4

Бренд: EFILive Страницы: 25

GMC Yukon Denali 2005

Бренд: Cadillac Страницы: 456

Бренд: Saab Страницы: 63

Бренд: R&G Страницы: 20

Бренд: Whispbar Страницы: 70

Бренд: Abrams Страницы: 12

Бренд: A-Tach Mounts Страницы: 2

Dynamic Power Management Home - Module

Бренд: newmotion Страницы: 20

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды