Mazda MX-5 Miata Sport 2007 Скачать руководство пользователя страница 1821 | Manualshive

Страница: 1821 / 2244

background image

function.)
Replace the power window main switch.
(See

POWER WINDOW MAIN

SWITCH
REMOVAL/INSTALLATION

.)

(power retractable hardtop model without
exterior open function/soft-top model.)

4



Measure the voltage at the power
window main switch terminal 1A.



Is the voltage B+?

Yes

Replace the power window main switch.
(See

POWER WINDOW MAIN

SWITCH
REMOVAL/INSTALLATION

.)

No

Inspect for an open or short circuit in the
power window main switch wiring harness
(battery power supply).
Inspect the power window main switch
connector connection. (damage/pulled-out
pins, corrosion)
Repair or replace if necessary.

5



Operate the power window using
the power window main switch



Does the power window motor
operate (rotate)?

CAUTION:



If the power window
motor temperature is
high, the motor may not
rotate due to the motor
internal bimetal function.
Leave it untouched for
about 3 min to cool it
down, then reinspect.

Yes

Go to the next step.

No

Replace the power window motor.
(See

POWER WINDOW REGULATOR

REMOVAL/INSTALLATION

.)

6



Remove the door glass from the
carrier plate.



Make sure that the door glass
moves smoothly using your hand.



Does the door glass move
smoothly?

Yes

Replace the power window regulator guide.

No

Inspect for a bent regulator guide or other
possible malfunction. If normal, replace the
glass run channel

7



Inspect the continuity between
power window main switch

NOTE:



Do not operate the power
window main switch during the
following inspection.

Yes

Go to the next step.

No

Replace the power window main switch.
(See

POWER WINDOW MAIN

SWITCH
REMOVAL/INSTALLATION

.)

2007 Mazda MX-5 Miata Sport

2007 ACCESSORIES & BODY, CAB Symptom Troubleshooting (Power Window System) - MX-5 Miata

Microsoft

Thursday, July 09, 2009 3:25:15 PM

Page 16

© 2005 Mitchell Repair Information Company, LLC.

«
...
1819
1820
1821
1822
1823
...
»

Содержание MX-5 Miata Sport 2007





































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для MX-5 Miata Sport 2007

Бренд: Hama Страницы: 2

Бренд: Triumph Страницы: 86

Бренд: FormFit Страницы: 4

Бренд: Honda Страницы: 32

2016 Sandero Stepway

Бренд: Renault Страницы: 183

Бренд: Alfa Romeo Страницы: 8

Бренд: Subaru Страницы: 16

Бренд: Kia Страницы: 51

Бренд: U.S. General Страницы: 8

Бренд: E&G Classics Страницы: 2

Бренд: Radical Sportscars Страницы: 44

Telescoping Computer Base C-TCB-34

Бренд: Havis-Shields Страницы: 1

Бренд: PEUGEOT Страницы: 107

Бренд: Edelbrock Страницы: 2

Бренд: Hudson Страницы: 77

Бренд: Lincoln Страницы: 538

Бренд: ULTIMATE SPEED Страницы: 26

Follow me RAPID INTRACKER

Бренд: Thule Страницы: 8

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды