Mazda MX-5 Miata Sport 2007 Скачать руководство пользователя страница 257 | Manualshive

Страница: 257 / 2244

background image

Courtesy of MAZDA MOTORS CORP.

5. Install in the reverse order of removal.

6. Turn the ignition switch to the ON position.

7. Verify that the air bag system warning light illuminates for

approx. 6 s

and goes out.



If the air bag system warning light does not operate normally, refer to

RESTRAINTS -- ON-

BOARD DIAGNOSTIC

system (air bag system) and perform inspection of the system.

CLOCK SPRING INSTALLATION NOTE

1. Adjust the clock spring after installing it. (See

CLOCK SPRING ADJUSTMENT

.)

CLOCK SPRING ADJUSTMENT

1. Set the front tires straight-ahead.

2. Turn the clock spring clockwise until it stops.

CAUTION:



If the clock spring is not adjusted, the spring wire in the clock spring
could over-wind and break when the steering wheel is turned. Always
adjust the clock spring after installing it.

NOTE:



The adjustment procedure is also specified on the caution label of the
clock spring.

CAUTION:



The clock spring will break if over-wound. Do not forcibly turn
the clock spring.

2008 Mazda MX-5 Miata Grand Touring

2008 RESTRAINTS Air Bag System - MX-5 Miata

Microsoft

Thursday, July 09, 2009 3:43:37 PM

Page 33

© 2005 Mitchell Repair Information Company, LLC.

«
...
255
256
257
258
259
...
»

Содержание MX-5 Miata Sport 2007





































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для MX-5 Miata Sport 2007

Бренд: RAM Commercial Страницы: 12

FRONT HEADLIGHT LENS COVER

Бренд: Bimmer Jakes Страницы: 4

Бренд: Carefree Страницы: 12

Бренд: Kolpin Страницы: 25

Бренд: Metra Electronics Страницы: 20

Бренд: SCC Страницы: 4

Бренд: Caltrend Страницы: 3

Бренд: POOL-LINE Страницы: 2

Бренд: Meritor Страницы: 20

SB-J-GCHER2/10W3v2

Бренд: Stealthbox Страницы: 2

Бренд: Ford Страницы: 4378

Бренд: Toyota Страницы: 549

Бренд: Feniex Страницы: 4

Бренд: Jaeger Страницы: 13

Бренд: Edelbrock Страницы: 4

Бренд: Kargo Master Страницы: 14

Бренд: Volkswagen Страницы: 2

Бренд: HG2 Страницы: 6

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды