Mazda MX-5 Miata Sport 2007 Скачать руководство пользователя страница 1633 | Manualshive

Страница: 1633 / 2244

background image

Fig. 11: Identifying Fasteners

Courtesy of MAZDA MOTORS CORP.

5. Slightly bent back the mudguard.

6. Remove the cover.

7. Remove the connector, then remove the discharge headlight bulb.

CAUTION:



The bulb generates extremely high heat when it is illuminated. If
the surface of the bulb is soiled, excessive heat will build up
and the life of the bulb will be shortened. When replacing the
bulb, hold the metal flange, not the glass. Wipe off any finger
prints before installation.

2007 Mazda MX-5 Miata Sport

2007 ACCESSORIES & BODY, CAB Lighting Systems - MX-5 Miata

Microsoft

Thursday, July 09, 2009 3:27:42 PM

Page 12

© 2005 Mitchell Repair Information Company, LLC.

«
...
1631
1632
1633
1634
1635
...
»

Содержание MX-5 Miata Sport 2007





































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для MX-5 Miata Sport 2007

Бренд: Wagan Страницы: 12

Бренд: Fabbri Страницы: 4

Бренд: Kia Страницы: 385

Бренд: Jackco Страницы: 11

Бренд: Porsche Страницы: 192

Бренд: Bestop Страницы: 11

Бренд: Whispbar Страницы: 14

2014 Insignia VXR SuperSport

Бренд: Vauxhall Страницы: 56

ANDROID INTERFACE

Бренд: GMC Страницы: 18

Бренд: Prorack Страницы: 15

Бренд: Subaru Страницы: 99

Бренд: BESAFE Страницы: 4

Бренд: MAXWORKS Страницы: 7

Бренд: AC Schnitzer Страницы: 16

Xplore Pro II SxS

Бренд: Marlon Страницы: 15

Ride-Rite Air Helper Springs 2173

Бренд: Firestone Страницы: 4

Бренд: SilverLeaf Electronics Страницы: 16

Бренд: Honda Страницы: 569

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды