Mazda MX-5 Miata Sport 2007 Скачать руководство пользователя страница 1242

Страница: 1242 / 2244

Fig. 62: Identifying Cable Case And Nut With Torque Specification

Courtesy of MAZDA MOTORS CORP.

6. Remove in the order indicated in the table.

Fig. 63: Identifying Power Retractable Hardtop Control Module Components

Courtesy of MAZDA MOTORS CORP.

7. Install in the reverse order of removal.

POWER RETRACTABLE HARDTOP CONTROL MODULE INSPECTION

1. Remove the following parts:

1. Console (See

CONSOLE REMOVAL/INSTALLATION

2. Quarter trim (See

QUARTER TRIM REMOVAL/INSTALLATION

2007 Mazda MX-5 Miata Sport

2007 ACCESSORIES & BODY, CAB Exterior Trim - MX-5 Miata

Microsoft

Thursday, July 09, 2009 3:32:13 PM

Page 42

«
...
1240
1241
1242
1243
1244
...
»

Содержание MX-5 Miata Sport 2007





































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание MX-5 Miata Sport 2007

Отзывы:

Похожие инструкции для MX-5 Miata Sport 2007

Бренды по названию

Популярные бренды

Mazda MX-5 Miata Sport 2007, Руководство пользователя

Результаты поиска

Содержание MX-5 Miata Sport 2007

Отзывы:

Похожие инструкции для MX-5 Miata Sport 2007

Бренды по названию

Популярные бренды