manualshive.com logo in svg

Mazda MX-5 Miata Sport 2007, Руководство пользователя, Страница: 628 / 2244

Поделиться
Скачать
Mazda MX-5 Miata Sport 2007 Скачать руководство пользователя страница 628

BRAKE PIPE REMOVAL NOTE 

1. Place an alignment mark on the brake pipe and dual proportioning valve. 

Fig. 25: Placing Alignment Mark On Brake Pipe & Dual Proportioning Valve

 

Courtesy of MAZDA MOTORS CORP.

 

DUAL PROPORTIONING VALVE INSTALLATION NOTE 

1. Install the dual proportioning valve so that the R marks faces the upper side of the vehicle. 

 

2007 Mazda MX-5 Miata Sport 

2007 BRAKES Conventional Brake System - MX-5 Miata

  

Microsoft 

 

Thursday, July 09, 2009 3:18:52 PM

Page 28 

© 2005 Mitchell Repair Information Company, LLC. 

Содержание MX-5 Miata Sport 2007





































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов