Mazda MX-5 Miata Sport 2007 Скачать руководство пользователя страница 426 | Manualshive

Страница: 426 / 2244

background image

Fig. 66: Identifying Piston Return Spring

74. Inspect the lining of all drive plates



If the lining is flaking or has changed color, or if it is worn or the print mark is wearing away,
replace with a new drive plate. When replacing, inspect the contact surfaces between the retaining
plate, driven plate and drive plate. If they are scratched or have changed color, replace with new
parts.

75. Blow compressed air into the oil passage as shown in the figure while pressing the B2 brake piston

component by hand and remove the B2 brake piston component from the transmission case.

Air pressure

392 kPa {4 kgf/cm

2

, 57 psi}

NOTE:



Before replacing with new drive plates, soak them at least 2 h in
ATF.

Fig. 67: Identifying Print Mark Location

2007 Mazda MX-5 Miata Sport

2006-08 TRANSMISSION Automatic Transmission Overhaul - MX-5 Miata & RX-8

Microsoft

Thursday, July 09, 2009 1:42:24 PM

Page 30

© 2005 Mitchell Repair Information Company, LLC.

«
...
424
425
426
427
428
...
»

Содержание MX-5 Miata Sport 2007





































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для MX-5 Miata Sport 2007

Бренд: ZAPTEC Страницы: 240

Бренд: Qube Страницы: 19

Бренд: Cadillac Страницы: 32

Бренд: Harbor Freight Tools Страницы: 4

Бренд: Webasto Страницы: 34

Бренд: STO N SHO Страницы: 7

Бренд: VER-MAC Страницы: 64

Бренд: Axxess Страницы: 8

Бренд: Dodge Страницы: 276

Бренд: CrimeStopper Страницы: 1

Бренд: TAUBENREUTHER Страницы: 18

Бренд: Toyota Страницы: 497

DH-RB 05.02 Series

Бренд: Dhollandia Страницы: 65

Бренд: Cadillac Страницы: 48

Бренд: EUFAB Страницы: 18

Бренд: DICE Страницы: 1

Бренд: Hudson Страницы: 24

Бренд: Mercedes-Benz Страницы: 24

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды