Mazda MX-5 Miata Sport 2007 Скачать руководство пользователя страница 188

Страница: 188 / 2244

6. Inspect for continuity between the hood latch switch terminals A and B



If there is continuity, replace the hood latch.

Fig. 31: Locking Hood Latch Using Flathead Screwdriver

Courtesy of MAZDA MOTORS CORP.

OPEN HOOK REMOVAL/INSTALLATION[ADVANCED KEYLESS SYSTEM]

1. Remove the following parts:

1. Console (See

CONSOLE REMOVAL/INSTALLATION

2. Quarter trim (See

QUARTER TRIM REMOVAL/INSTALLATION

3. Scuff plate (See

SCUFF PLATE REMOVAL/INSTALLATION

4. Tire house trim (See

TIRE HOUSE TRIM REMOVAL/INSTALLATION

5. Aeroboard (See

AEROBOARD REMOVAL/INSTALLATION

6. Seat back bar garnish (See

SEAT BACK BAR GARNISH REMOVAL/INSTALLATION

7. Back trim (See

BACK TRIM REMOVAL/INSTALLATION

8. Seat back bar lower garnish (See

SEAT BACK BAR LOWER GARNISH

REMOVAL/INSTALLATION

2. Remove the bolts.

3. Remove the open hook.

4. Install in the reverse order of removal.

CAUTION:



After the inspection, unlock the hood latch. If closing the hood
with the hood latch locked, the hood latch and/or hood striker
may be broken.

2007 Mazda MX-5 Miata Sport

2007 ACCESSORIES & BODY, CAB Security and Locks (Advanced Keyless System) - MX-5 Miata

Microsoft

Thursday, July 09, 2009 3:36:54 PM

Page 29

Содержание MX-5 Miata Sport 2007





































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание MX-5 Miata Sport 2007

Отзывы:

Похожие инструкции для MX-5 Miata Sport 2007

Бренды по названию

Популярные бренды

Mazda MX-5 Miata Sport 2007, Руководство пользователя

Результаты поиска

Содержание MX-5 Miata Sport 2007

Отзывы:

Похожие инструкции для MX-5 Miata Sport 2007

Бренды по названию

Популярные бренды