Mazda MX-5 Miata Sport 2007 Скачать руководство пользователя страница 721 | Manualshive

Страница: 721 / 2244

background image

ENGINE COOLANT LEVEL INSPECTION [LF]

1. Verify that the engine coolant level in the coolant reserve tank is between the L and F marks.

2. If the engine coolant level is below L mark, add engine coolant.



When you are sure all the pressure is gone, press down on the cap
using the cloth, turn it, and remove it.

WARNING:



Never remove the cooling system cap or loosen the radiator drain
plug while the engine is running, or when the engine and radiator
are hot. Scalding engine coolant and steam may shoot out and
cause serious injury. It may also damage the engine and cooling
system.



Turn off the engine and wait until it is cool. Even then, be very
careful when removing the cap. Wrap a thick cloth around it and
slowly turn it counterclockwise to the first stop. Step back while the
pressure escapes.



When you are sure all the pressure is gone, press down on the cap
using the cloth, turn it, and remove it.

NOTE:



If the "FL22" mark is shown on or near the cooling system cap, use FL22
type engine coolant.



FL22 type engine coolant is shipped as a diluted solution (55% coolant,
45% water). Use the solution as is when replacing coolant.

2007 Mazda MX-5 Miata Sport

2007 ENGINE Cooling System - MX-5 Miata

Microsoft

Thursday, July 09, 2009 3:06:06 PM

Page 2

© 2005 Mitchell Repair Information Company, LLC.

«
...
719
720
721
722
723
...
»

Содержание MX-5 Miata Sport 2007





































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для MX-5 Miata Sport 2007

Бренд: Harmar Mobility Страницы: 10

Бренд: CALIMA Страницы: 9

Бренд: FALCON RIDGE Страницы: 8

Бренд: Scosche Страницы: 8

Бренд: Porsche Страницы: 313

ADARAC Aluminum M Series

Бренд: aci Страницы: 16

Бренд: Imiola HAK-POL Страницы: 3

Бренд: Jaeger Страницы: 11

Бренд: Rugged Ridge Страницы: 3

Бренд: SilverLeaf Electronics Страницы: 16

Бренд: Yakima Страницы: 28

Бренд: PEUGEOT Страницы: 232

EPS-LD SafePark

Бренд: Tobe Страницы: 2

Бренд: Bulldog Security Страницы: 7

Бренд: Conrad Страницы: 8

Бренд: Lincoln Страницы: 364

Aura Mobile BT MCP-2014

Бренд: Spracht Страницы: 2

DODGE AD100 1993

Бренд: Chrysler Страницы: 1502

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды