Mazda MX-5 Miata Sport 2007 Скачать руководство пользователя страница 1682

Страница: 1682 / 2244

3. Remove the column cover. (See

COLUMN COVER REMOVAL/INSTALLATION

4. Remove the ignition key illumination bulb.

5. Install in the reverse order of removal.

Fig. 61: Identifying Ignition Key Illumination Bulb

Courtesy of MAZDA MOTORS CORP.

DOOR SWITCH REMOVAL/INSTALLATION

1. Remove the battery cover.

2. Disconnect the negative battery cable. (See

BATTERY REMOVAL/INSTALLATION [LF]

3. Disassemble in the order indicated in

Fig. 62

2007 Mazda MX-5 Miata Sport

2007 ACCESSORIES & BODY, CAB Lighting Systems - MX-5 Miata

Microsoft

Thursday, July 09, 2009 3:27:42 PM

Page 61

«
...
1680
1681
1682
1683
1684
...
»

Содержание MX-5 Miata Sport 2007





































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание MX-5 Miata Sport 2007

Отзывы:

Похожие инструкции для MX-5 Miata Sport 2007

Бренды по названию

Популярные бренды

Mazda MX-5 Miata Sport 2007, Руководство пользователя

Результаты поиска

Содержание MX-5 Miata Sport 2007

Отзывы:

Похожие инструкции для MX-5 Miata Sport 2007

Бренды по названию

Популярные бренды