Mazda MX-5 Miata Sport 2007 Скачать руководство пользователя страница 1214

Страница: 1214 / 2244

Fig. 17: Identifying Rivet

Courtesy of MAZDA MOTORS CORP.

7. Remove the nut, then remove the cable end bracket.

Fig. 18: Identifying Cable End Bracket & Nut With Torque Specifications

Courtesy of MAZDA MOTORS CORP.

RAIN RAIL DISASSEMBLY NOTE

1. Remove the rivets from the top fabric using a drill.

SPRING A DISASSEMBLY NOTE

1. Remove the bolt.

2. Remove the spacers, spring and collars from the link.

Fig. 19: Identifying Spacers, Spring & Collars

Courtesy of MAZDA MOTORS CORP.

SPRING B DISASSEMBLY NOTE

1. Remove the bolt.

2. Pull the link in the direction of the arrow to remove the spacer and spring.

2007 Mazda MX-5 Miata Sport

2007 ACCESSORIES & BODY, CAB Exterior Trim - MX-5 Miata

Microsoft

Thursday, July 09, 2009 3:32:12 PM

Page 14

«
...
1212
1213
1214
1215
1216
...
»

Содержание MX-5 Miata Sport 2007





































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание MX-5 Miata Sport 2007

Отзывы:

Mazda MX-5 Miata Sport 2007, Руководство пользователя, Страница: 1214 / 2244

Результаты поиска

Содержание MX-5 Miata Sport 2007

Отзывы: