Mazda MX-5 Miata Sport 2007 Скачать руководство пользователя страница 958 | Manualshive

Страница: 958 / 2244

background image

Fig. 45: Releasing Locks Between Retainer And Joint Port

Courtesy of MAZDA MOTORS CORP.

2. Pull out the hose straight from the joint port and disconnect it.

3. Cover the disconnected quick release connector and joint port with vinyl sheeting or a similar material to

prevent it from becoming scratched or dirty.

TYPE A INSTALLATION

NOTE:



The retainer is attached to the pipe even after the connector is
disconnected.

NOTE:



If the quick release connector O-ring is damaged or has slipped, replace
the evaporative hose.



A checker tab is integrated with the quick release connector for new
evaporative hoses. Remove the checker tab from the quick release
connector after the connector is completely engaged with the joint port.

2007 Mazda MX-5 Miata Sport

2007 ENGINE PERFORMANCE Emission System - MX-5 Miata

Microsoft

Thursday, July 09, 2009 2:38:04 PM

Page 44

© 2005 Mitchell Repair Information Company, LLC.

«
...
956
957
958
959
960
...
»

Содержание MX-5 Miata Sport 2007





































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для MX-5 Miata Sport 2007

Бренд: Calira Страницы: 14

Бренд: Kathrein Страницы: 7

Бренд: UMBRA RIMORCHI Страницы: 18

Бренд: Vauxhall Страницы: 199

Бренд: Chevrolet Страницы: 356

Бренд: Ford Страницы: 272

Бренд: Pontiac Страницы: 376

Бренд: Jeep Страницы: 712

Бренд: Safe Fleet Страницы: 11

Бренд: Camec Страницы: 19

Бренд: PEUGEOT Страницы: 249

Бренд: Nav TV Страницы: 2

Бренд: CTEK Страницы: 84

Бренд: Kuda Страницы: 2

Бренд: TEINHOF Страницы: 2

Бренд: Ford Страницы: 52

Бренд: Xingyun Страницы: 74

Бренд: Saab Страницы: 288

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды