Mazda MX-5 Miata Sport 2007 Скачать руководство пользователя страница 1746 | Manualshive

Страница: 1746 / 2244

background image

1. Move the steering wheel as shown in

Fig. 7

to inspect for column bearing wear, steering shaft joint play,

steering wheel looseness, and column looseness.



Repair or replace as necessary.

Fig. 7: Inspecting Steering Wheel Play

Courtesy of MAZDA MOTORS CORP.

STEERING WHEEL EFFORT INSPECTION

1. Inspect the following points:



Tire size and tire pressure



Fluid level



Drive belt deflection

2. With the vehicle on a hard, level surface, put the wheels in the straight-ahead position.

3. Remove the air bag module.

WARNING:



Handling the air bag module improperly can accidentally
deploy the air bag module, which may seriously injure you.
Read AIR BAG SYSTEM WARNINGS before handling the air

2007 Mazda MX-5 Miata Sport

2007 STEERING Power Steering - MX-5 Miata

Microsoft

Thursday, July 09, 2009 2:11:38 PM

Page 8

© 2005 Mitchell Repair Information Company, LLC.

«
...
1744
1745
1746
1747
1748
...
»

Содержание MX-5 Miata Sport 2007





































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для MX-5 Miata Sport 2007

Бренд: Yakima Страницы: 12

Бренд: JEHNERT SOUND DESIGN Страницы: 8

Experience Series

Бренд: Rainbow Страницы: 19

Бренд: Yakima Страницы: 12

Бренд: Barker Страницы: 2

Бренд: Horn Tools Страницы: 6

Бренд: Saab Страницы: 3

Бренд: Hama Страницы: 75

Бренд: Harman Kardon Страницы: 16

Бренд: TATA Motors Страницы: 184

PW-50C Civilian

Бренд: B&G electronics Страницы: 7

TRI-FOLD PG9300RF

Бренд: Pet Gear Страницы: 4

Бренд: Quadratec Страницы: 12

Бренд: Jaeger Страницы: 11

Бренд: Thule Страницы: 8

Бренд: Prorack Страницы: 14

Giulietta 2.0 JTDM

Бренд: Alfa Romeo Страницы: 14

CMPC-22 Fujitsu-Siemens PocketLoox 410

Бренд: Carcomm Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды