Mazda MX-5 Miata Sport 2007 Скачать руководство пользователя страница 1040 | Manualshive

Страница: 1040 / 2244

background image

Fig. 49: Identifying PCM Harness Side Connector
Courtesy of MAZDA MOTORS CORP.

Open Circuit



If there is no continuity in the following wiring harnesses, there is an open circuit. Repair or replace the
wiring harness.



APP sensor terminal A and PCM terminal 1AJ



APP sensor terminal B and PCM terminal 1AV



APP sensor terminal C and PCM terminal 1AP



APP sensor terminal D and PCM terminal 1AL



APP sensor terminal E and PCM terminal 1AS



APP sensor terminal F and PCM terminal 1AO

Short Circuit



If there is continuity in the following wiring harnesses, there is a short circuit. Repair or replace the
wiring harness.



APP sensor terminal A and body ground



APP sensor terminal B and power supply



APP sensor terminal C and body ground



APP sensor terminal C and power supply



APP sensor terminal D and body ground



APP sensor terminal E and power supply



APP sensor terminal F and body ground



APP sensor terminal F and power supply

CRANKSHAFT POSITION (CKP) SENSOR INSPECTION [LF]

AIR GAP INSPECTION

1. Verify that the CKP sensor is securely installed.

2. Using a thickness gauge, measure the air gap between the plate projections at the back of crankshaft

pulley and the CKP sensor.



If not within the specification, inspect the plate projections for cracks or bending.



If there is any malfunction, replace the crankshaft pulley. (See

ENGINE

REMOVAL/INSTALLATION [LF]

.)

NOTE:



Before performing the following inspection, make sure to follow the
procedure as indicated in the troubleshooting flow diagram. (See
TROUBLESHOOTING PROCEDURE .)

2007 Mazda MX-5 Miata Sport

2007 ENGINE PERFORMANCE Engine Control System - MX-5 Miata

Microsoft

Thursday, July 09, 2009 2:41:10 PM

Page 75

© 2005 Mitchell Repair Information Company, LLC.

«
...
1038
1039
1040
1041
1042
...
»

Содержание MX-5 Miata Sport 2007





































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для MX-5 Miata Sport 2007

Бренд: Jeda Страницы: 8

Бренд: Jeep Страницы: 496

Бренд: Fabbri Страницы: 4

SmartDiag2GO GD201-O

Бренд: OCTO Страницы: 5

Бренд: Kolpin Страницы: 25

Бренд: BURY Страницы: 2

Бренд: Kia Страницы: 51

Бренд: Quadratec Страницы: 14

Бренд: Mitsubishi Страницы: 367

Бренд: Toyota Страницы: 285

Бренд: Pet Gear Страницы: 4

IGNIS 2022 Series

Бренд: Suzuki Страницы: 570

Бренд: Westin Страницы: 3

Бренд: chinavasion Страницы: 3

Бренд: Audiovox Страницы: 2

Бренд: Mercedes-Benz Страницы: 434

Бренд: Prorack Страницы: 13

Sightline VIMCF-93C

Бренд: Crux Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды