Mazda MX-5 Miata Sport 2007 Скачать руководство пользователя страница 848

Страница: 848 / 2244

Fig. 17: Locating DLC-2 Connector

Courtesy of MAZDA MOTORS CORP.

5. After the vehicle is identified, select the following items from the initial screen of the M-MDS.



When using the IDS (laptop PC)

1. Select "Chassis".

2. Select "ABS/DSC".

3. Select "Sensor Initialization".



When using the PDS (Pocket PC)

1. Select "All Tests and Calibrations".

2. Select "Sensor Initialization".

6. Drive the vehicle forward.

7. After 5 min of driving, verify that the DSC system is normal.

BRAKE FLUID PRESSURE SENSOR INSPECTION

1. Turn the ignition switch off.

2. Install the

SSTs

to the master cylinder.

NOTE:



Install the SST (49 N043 001) to the master cylinder using a
commercially available flare nut wrench.

2007 Mazda MX-5 Miata Sport

2007 BRAKES Dynamic Stability Control - MX-5 Miata

Microsoft

Thursday, July 09, 2009 3:17:05 PM

Page 25

Содержание MX-5 Miata Sport 2007





































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание MX-5 Miata Sport 2007

Отзывы:

Похожие инструкции для MX-5 Miata Sport 2007

Бренды по названию

Популярные бренды

Mazda MX-5 Miata Sport 2007, Руководство пользователя

Результаты поиска

Содержание MX-5 Miata Sport 2007

Отзывы:

Похожие инструкции для MX-5 Miata Sport 2007

Бренды по названию

Популярные бренды