Mazda MX-5 Miata Sport 2007 Скачать руководство пользователя страница 561

Страница: 561 / 2244

Fig. 351: Identifying Transmission Case Bolts

113. Remove the silicons sealant and be careful not to spill any oil on the contact surface of the transmission

case and extension housing.

114. Clean the contact surface of the transmission case and the extension housing, and the bolt holes.

115. Apply sealant to the extension housing as shown in the figure.

116. Install the extension housing and transmission case.

Fig. 352: Identifying Sealant Application Area On Extension Housing

117. Temporarily tighten the bolts by hand as shown in the figure.

NOTE:



Completely remove sealant and oil with isoproply alcohol (IPA) or
similar.

NOTE:



Spread sealant over the contact surface.

2007 Mazda MX-5 Miata Sport

2006-08 TRANSMISSION Automatic Transmission Overhaul - MX-5 Miata & RX-8

Microsoft

Thursday, July 09, 2009 1:42:26 PM

Page 165

Содержание MX-5 Miata Sport 2007





































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание MX-5 Miata Sport 2007

Отзывы:

Похожие инструкции для MX-5 Miata Sport 2007

Бренды по названию

Популярные бренды

Mazda MX-5 Miata Sport 2007, Руководство пользователя

Результаты поиска

Содержание MX-5 Miata Sport 2007

Отзывы:

Похожие инструкции для MX-5 Miata Sport 2007

Бренды по названию

Популярные бренды